Signature Kitchen Suite SKSUD2402P Скачать руководство пользователя

Страница: 11 / 28

INSTALLATION

ENGLISH

NOTE

• This unit is designed to be customized with a

decorative panel. A field-installed custom door

panel or an optional Stainless Steel Panel Kit is

required.

•

For Custom Panels:

Use templates provided

with units to pre-drill holes for mounting panel

brackets (provided with unit). Adjustment screws

and instructionsalso provided with units.

• Optional accessories

SKSUK240DS - Stainless Steel Panel and

Handle Kit for 24-inch Undercounter

Drawer Refrigerator

This unit can be installed with an optional

Stainless Steel Panel Kit. Kit includes two drawer

panels and two handles.

SKSUK240WS - Stainless Steel Panel and

Handle Kit for 24-inch Undercounter

Wine Refrigerator

This unit can be installed with an optional

Stainless Steel Panel Kit. Kit includes door panel

and handle.

Custom Panel Dimensions

3/4" (19 mm) Custom panel dimensions – Flush

installation
• 24-inch undercounter convertible drawer

refrigerator

NOTE

• The custom panel dimensions are same for the

Upper and Lower drawers.

• 24-inch built-in undercounter wine refrigerator

Installing the Anti-tip Brackets

WARNING

• To avoid injury or damage, check for electrical

wires or plumbing in walls before drilling or

installing screws.

• The Anti –Tip bracket should be firmly fixed to a

concrete wall/wood with strength of 15 t or

greater, or a wall with equivalent strength. (The

structure where the bracket is fixed should be a

solid structure that can withstand a force of 70

kgf or greater.)

3/4" (19 mm)

Dimensions

23 11/16" (602 mm)

15" (381 mm)

Dimensions

23 1/16" (602 mm)

3 11/32" (84.9 mm)

4 15/16" (124.9 mm)

30 1/3" (769 mm)

Содержание SKSUD2402P





























Результаты поиска

Содержание SKSUD2402P

Отзывы:

Похожие инструкции для SKSUD2402P

Бренды по названию

Популярные бренды

Signature Kitchen Suite SKSUD2402P, Руководство по установке

Результаты поиска

Содержание SKSUD2402P

Отзывы:

Похожие инструкции для SKSUD2402P

Бренды по названию

Популярные бренды