background image

SC5312A Operating & Programming Manual 

Rev 1.0.2 

 

I

M P O R T A N T  

I

N F O R M A T I O N

 

Warranty 

This product is warranted against defects in materials and workmanship for a period of three years from 
the date of shipment. SignalCore will, at its option, repair or replace equipment that proves to be defective 
during the warranty period. This warranty includes parts and labor. 
 
Before  any  equipment  will  be  accepted  for  warranty  repair  or  replacement,  a  Return  Material 
Authorization (RMA) number must be obtained from a SignalCore customer service representative and 
clearly marked  on  the  outside  of  the  return  package.  SignalCore  will  pay  all  shipping  costs  relating  to 
warranty repair or replacement. 
 
SignalCore strives to make the information in this document as accurate as possible. The document has 
been  carefully  reviewed  for  technical  and  typographic  accuracy.  In  the  event  that  technical  or 
typographical errors exist, SignalCore reserves the right to make changes to subsequent editions of this 
document  without  prior  notice  to  possessors  of  this  edition.  Please  contact  SignalCore  if  errors  are 
suspected. In no event shall SignalCore be liable for any damages arising out of or related to this document 
or the information contained in it. 

EXCEPT  AS  SPECIFIED  HEREIN,  SIGNALCORE,  INCORPORATED  MAKES  NO  WARRANTIES,  EXPRESS  OR 
IMPLIED,  AND  SPECIFICALLY  DISCLAIMS  ANY  WARRANTY  OF  MERCHANTABILITY  OR  FITNESS  FOR  A 

PARTICULAR PURPOSE. CUSTOMER’S RIGHT TO REC

OVER DAMAGES CAUSED BY FAULT OR NEGLIGENCE 

ON  THE  PART  OF  SIGNALCORE,  INCORPORATED  SHALL  BE  LIMITED  TO  THE  AMOUNT  THERETOFORE 
PAID BY THE CUSTOMER. SIGNALCORE, INCORPORATED WILL NOT BE LIABLE FOR DAMAGES RESULTING 
FROM LOSS OF DATA, PROFITS, USE OF PRODUCTS, OR INCIDENTAL OR CONSEQUENTIAL DAMAGES, 
EVEN IF ADVISED OF THE POSSIBILITY THEREOF

. This limitation of the liability of SignalCore, Incorporated 

will apply regardless of the form of action, whether in contract or tort, including negligence. Any action 
against  SignalCore,  Incorporated  must  be  brought  within  one  year  after  the  cause  of  action  accrues. 
SignalCore,  Incorporated  shall  not  be  liable  for  any  delay  in  performance  due  to  causes  beyond  its 
reasonable  control.  The  warranty  provided  herein  does  not  cover  damages,  defects,  malfunctions,  or 
service 

failures caused by owner’

s failure to follow SignalCore, Incorporated

’s 

installation, operation, or 

maintenance instructions; owner’s modification of the

 

product; owner’s abuse, misuse, or negligent acts; 

and  power  failure  or  surges,  fire,  flood,  accident,  actions  of  third  parties,  or  other  events  outside 
reasonable control. 

Copyright & Trademarks 

Under the copyright laws, this publication may not be reproduced or transmitted in any form, electronic 
or  mechanical,  including  photocopying,  recording,  storing  in  an  information  retrieval  system,  or 
translating, in whole or in part, without the prior written consent of SignalCore, Incorporated. 

SignalCore, Incorporated respects the intellectual property rights of others, and we ask those who use our 
products to do the same. Our products are protected by copyright and other intellectual property laws. 
Use of SignalCore products is restricted to applications that do not infringe on the intellectual property 
rights of others. 

Содержание SC5312A

































Отзывы: