SIGNALCORE 7100036-01 страница 7 Скачать руководство пользователя | Manualshive

Страница: 7 / 40

background image

SC5506A Operating & Programming Manual

Rev 2.1.1

3

SignalCore products meet the essential requirements of Directives 2014/30/EU (EMC) and 2014/35/EU
(product safety) and comply with the relevant standards. Standards for Measurement, Control and
Laboratory Equipment include EN 61326-1:2013 and EN 55011:2009 for EMC, and EN 61010-1 for product
safety.

Recycling Information

All products sold by SignalCore eventually reach the end of their useful life. SignalCore complies with EU
Directive 2012/19/EU regarding Waste Electrical and Electronic Equipment (WEEE).

Warnings Regarding Use of SignalCore Products

(1)

PRODUCTS FOR SALE BY SIGNALCORE, INCORPORATED ARE NOT DESIGNED WITH COMPONENTS NOR TESTED FOR A LEVEL OF
RELIABILITY SUITABLE FOR USE IN OR IN CONNECTION WITH SURGICAL IMPLANTS OR AS CRITICAL COMPONENTS IN ANY LIFE SUPPORT
SYSTEMS WHOSE FAILURE TO PERFORM CAN REASONABLY BE EXPECTED TO CAUSE SIGNIFICANT INJURY TO A HUMAN.

(2)

IN  ANY  APPLICATION,  INCLUDING  THE  ABOVE,  RELIABILITY  OF  OPERATION  OF  THE  SOFTWARE  PRODUCTS  CAN  BE  IMPAIRED  BY
ADVERSE  FACTORS,  INCLUDING  BUT  NOT  LIMITED  TO  FLUCTUATIONS  IN  ELECTRICAL  POWER  SUPPLY,  COMPUTER  HARDWARE
MALFUNCTIONS, COMPUTER OPERATING SYSTEM SOFTWARE FITNESS, FITNESS OF COMPILERS AND DEVELOPMENT SOFTWARE USED
TO DEVELOP AN APPLICATION, INSTALLATION ERRORS, SOFTWARE AND HARDWARE COMPATIBILITY PROBLEMS, MALFUNCTIONS OR
FAILURES OF ELECTRONIC MONITORING OR CONTROL DEVICES, TRANSIENT FAILURES OF ELECTRONIC SYSTEMS (HARDWARE AND/OR
SOFTWARE),  UNANTICIPATED  USES  OR  MISUSES,  OR  ERRORS  ON  THE  PART  OF  THE  USER  OR  APPLICATIONS  DESIGNER  (ADVERSE

FACTORS SUCH AS THESE ARE HEREAFTER COLLECTIVELY TERMED “SYSTEM FAILURES”). ANY APPLICATION WHERE A SYSTEM FAILU

RE

WOULD CREATE A RISK OF HARM TO PROPERTY OR PERSONS (INCLUDING THE RISK OF BODILY INJURY AND DEATH) SHOULD NOT BE
SOLELY RELIANT UPON ANY ONE COMPONENT DUE TO THE RISK OF SYSTEM FAILURE. TO AVOID DAMAGE, INJURY, OR DEATH, THE
USER OR APPLICATION DESIGNER MUST TAKE REASONABLY PRUDENT STEPS TO PROTECT AGAINST SYSTEM FAILURES, INCLUDING BUT
NOT LIMITED TO BACK-UP OR SHUT DOWN MECHANISMS. BECAUSE EACH END-USER SYSTEM IS CUSTOMIZED AND DIFFERS FROM
SIGNALCORE'  TESTING  PLATFORMS,  AND  BECAUSE  A  USER  OR  APPLICATION  DESIGNER  MAY  USE  SIGNALCORE  PRODUCTS  IN
COMBINATION  WITH  OTHER  PRODUCTS  IN  A  MANNER  NOT  EVALUATED  OR  CONTEMPLATED  BY  SIGNALCORE,  THE  USER  OR
APPLICATION DESIGNER IS ULTIMATELY RESPONSIBLE FOR VERIFYING AND VALIDATING THE SUITABILITY OF SIGNALCORE PRODUCTS
WHENEVER  SIGNALCORE  PRODUCTS  ARE  INCORPORATED  IN  A  SYSTEM  OR  APPLICATION,  INCLUDING,  WITHOUT  LIMITATION,  THE
APPROPRIATE DESIGN, PROCESS AND SAFETY LEVEL OF SUCH SYSTEM OR APPLICATION.

«
...
5
6
7
8
9
...
»

Содержание 7100036-01









































Отзывы:

Нет отзывов

Похожие инструкции для 7100036-01

Бренд: iMode Страницы: 16

Бренд: TECHWOOD Страницы: 16

Бренд: Hamilton Beach Страницы: 92

Бренд: Eickemeyer Страницы: 28

Бренд: THORLABS Страницы: 33

Бренд: cecotec Страницы: 60

Бренд: at professional Страницы: 20

Fresh Express DJ755G

Бренд: Moulinex Страницы: 10

Бренд: Moulinex Страницы: 31

Бренд: Moulinex Страницы: 39

Бренд: Moulinex Страницы: 16

Бренд: MAGIMIX Страницы: 52

Бренд: Gardol Страницы: 40

DAS-4300 Series

Бренд: Keithley Страницы: 94

Бренд: Harman Kardon Страницы: 32

Бренд: Bosch Страницы: 56

Бренд: Bosch Страницы: 73

Бренд: Bosch Страницы: 102

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды