SIGMATEK DIAS-DRIVE 210-23 Скачать руководство пользователя страница 71 | Manualshive

Страница: 71 / 91

SIGMATEK DIAS-DRIVE 210-23 Скачать руководство пользователя страница 71

DIAS-DRIVE 210-23

30.03.2021

Page 71

7.6 Additional Information

7.6.1 "Safe Restart" STO (Safe Torque Off)

The  DIAS  Drive,  in  combination  with  the  optional  VARAN  interface,  supports  the  safety
functions  SS1  (Safe  Stop  1)  and  STO  (Safe  Torque  Off),  and  meets  the  requirements  for
Category 4 Performance Level "e" according to EN ISO 13849-1 and SIL3 according to EN
62061.
For his purpose, the servo amplifier has two safe inputs ENABLE_L und ENABLE_H.

The  relay  output  S1/S2  can  be  used  to  provide  the  status  of  the  safety  function.  It  is  not
safety-relevant, but can be used to test the external safety function.

The stop brake control is not a component of the safety function. If a safe shutdown of the
stop brake is required, the +24 V-BR brake supply must also be shut down externally.

For the 24 V supply, only PELV/SELV can be used.

«
...
69
70
71
72
73
...
»

Содержание DIAS-DRIVE 210-23




























































































Отзывы:

Нет отзывов