SIGMATEK DIAS-DRIVE 210-23 Скачать руководство пользователя страница 55

Страница: 55 / 91

DIAS-DRIVE 210-23

30.03.2021

Page 55

Host

communica-

tion

─ No new values were

transmitted for two suc-
cessive cycles

─ Internal communication

error with the interface

─ Synchronization is not engaged,

check A-CTIME and the cycle
time of the control

─ Check A-STIME
─ Communication interrupted,

check

─ see also I-DERROR

Amplifier error E2
(I-DERROR)

─ Various internal errors

─ see also

I-DERROR

─ Contact manufacturer

Amplifier error E1
(I-DERROR)

─ Various internal errors

─ see also

I-DERROR

─ Contact manufacturer

Power output error:
─ Motor cable has a ground

fault

─ The motor has a ground

fault

─ Output stage defective

─ Check motor cable, exchange if
necessary
─ Exchange the motor
─ Exchange amplifier

Ballast circuit error
─ Ballast cable has a ground

fault

─ Ballast resistor has a

ground error

─ Ballast output defective

─ Exchange ballast cable

─ Exchange ballast resistor

─ Exchange amplifier

"Enable

locked"

error

─ The amplifier is "enabled"

in the software when one
of safety inputs still has
"low" a signal.

─ Enable amplifier only if ENABLE

and
EN-BRAKE are "high".

Driver voltage error

─ The amplifier is "enabled"

in the software when
"Lock" still has a signal.

─ Enable the amplifier only if the

LOCK signal is "high".

DC over voltage
and

brake

re-

sistance

limit

reached.

─ Brake resistance power is

insufficient. Brake re-
sistance power has been
reached and the resistor
was deactivated.

─ An external brake resistor must

be used to adjust the value of

G-MBAL

Brake supply error:

─ Stop brake voltage 24V-

BR missing.

─ Stop brake switch defec-

tive.

─ If the motor has a stop brake,

the amplifier can only be "ena-
bled" when 24V-BR is applied
to the stop brake.

─ Exchange amplifier

Reserved

I2t error

─ I-I2T has exceeded the

warning value A-I2TERR .

─ Increase A-I2TERR.

Motor temperature
warning

─ I-TEMPM has exceeded

the warning value A-
TEMPMW.

─ Increase A-TEMPMW.

Содержание DIAS-DRIVE 210-23




























































































Результаты поиска

Содержание DIAS-DRIVE 210-23

Отзывы:

SIGMATEK DIAS-DRIVE 210-23, Руководство пользователя, Страница: 55 / 91

Результаты поиска

Содержание DIAS-DRIVE 210-23

Отзывы: