background image

CCP 621 

C-DIAS PROSESSOR MODULE

 

 

 

Page 28  

27.03.2020 

15  Status and Error Messages 

Status  an  error  messages  are  displayed  in  the  LASAL  CLASS  software  status  test.  If  the 
CPU has a status display, the status or error number is also show here as well. POINTER 
or CHKSUM messages can also be shown on the terminal screen. 
 

Number

 

Message 

Definition 

Cause/solution 

00 

RUN RAM 

The  user  program  is  currently  running  in 
RAM. 

The display is not affected. 

 

01

 

RUN ROM 

The  user  program  stored  in  the  program 
memory  module  loaded  into  the  RAM  is 
currently running. 

The display is not affected. 

 

02 

RUNTIME 

The total time for all cyclic objects exceed the 
maximum  time;  the  time  can  be  configured 
using two system variables: 

- Runtime: time remaining 

-  SWRuntime: pre-selected value for the 

runtime counter 

 

03 

POINTER 

Incorrect  program  pointers  were  detected 
before running the user program 

Possible Causes: 

The program memory module is 

missing,  not programmed or defective. 

The program in the user program 

  memory (RAM) is not  

exe-

cutable. 

Software error, overwrites the user 

program.  

 

Solution: 

Reprogram the memory module, 

  if the error reoccurs exchange the 
module. 

Correct programming error 

04 

CHKSUM 

An  invalid  checksum  was  detected  before 
running the user program. 

Cause/solution: s. POINTER 

 

Содержание CCP 621















































Отзывы: