SIGLENT SVA1000X Series Скачать руководство пользователя страница 131

Страница: 131 / 140

SIG

ENT

SVA1000X User Manual 113

7.2 Build Communication

7.2.1 Build Communication Using VISA

NI-VISA includes a Run-Time Engine version and a Full version. The Run-Time Engine version

provides NI device drivers such as USB-TMC, VXI, GPIB, etc. The full version includes the Run-Time

Engine and a software tool named NI MAX that provides a user interface to control the device.

You can get NI-VISA full version from:

http://www.ni.com/download/

After download you can follow the steps below to install it:

Double click the visa_full.exe, dialog shown as below:

Click Unzip, the installation process will automatically launch after unzipping files. If your computer

needs to install .NET Framework 4, its setup process will auto start.

The NI-VISA installing dialog is shown above. Click Next to start the installation process.

Содержание SVA1000X Series













































































































































Результаты поиска

Содержание SVA1000X Series

Отзывы:

SIGLENT SVA1000X Series, Руководство пользователя, Страница: 131 / 140

Результаты поиска

Содержание SVA1000X Series

Отзывы: