SIGLENT SSG3000X Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 38

background image

SIGLENT

6 SSG3000X Service Manual

Preparation Information

Before initiating performance verification or any adjustments, it is
recommended to follow these procedures. The following topics are discussed
in this chapter.



How to perform functional checks



How to operate performance verification test

For more detailed information about the signal generator operation, please

refer to the SSG3000X User Manual.

Functional check

There are three types of checks used to determine if the signal generator is

operating properly.

Power-on Inspection

The normal operating voltage for SSG3000X series signal generators is in the
range of 100-240 VRMS, 50 Hz/ 60 Hz/ 440 Hz.

Please use the power cord provided with the accessories to connect the
instrument to the power source as shown in the figure below.

Figure 1-1 Connect power cord

Note: To avoid electric shock, make sure that the instrument is

correctly grounded to the earth before connecting AC power.

Press the power-on button located at the lower left corner of the front panel

and several keys will illuminate for about 6 seconds. Then, the boot screen will

appear on the display.

The front panel is shown in the figure below.

«
...
4
5
6
7
8
...
»

Содержание SSG3000X







































Отзывы:

Нет отзывов

Похожие инструкции для SSG3000X

HDG3000B Series

Бренд: Hantek Страницы: 22

Бренд: GENMAX Страницы: 28

Бренд: Goodmans Страницы: 12

Бренд: Porter-Cable Страницы: 24

12.0 BTDAR 50 HERTZ

Бренд: Westerbeke Страницы: 82

Music Angel 12031

Бренд: QooPro Страницы: 24

Бренд: Radio Shack Страницы: 4

Бренд: King Canada Страницы: 11

Бренд: GENMAX Страницы: 8

Бренд: Parkside Страницы: 120

Бренд: Craig Страницы: 7

Бренд: Craig Страницы: 8

Бренд: Craig Страницы: 22

Бренд: Honda Страницы: 59

Бренд: Philips Страницы: 16

Бренд: Philips Страницы: 1

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды