manualshive.com logo in svg

Sigineer Power M12048D, Руководство пользователя

Поделиться
Скачать
Sigineer Power M12048D Скачать руководство пользователя страница 28

                                                                                                                                            www.sigineer.com 

28 

⚫

 

SUITABLE FOR MOUNTING ON CONCRETE OR OTHER NON-COMBUSTIBLE SURFACE 
ONLY 

⚫

 

Use screws, bolts, or other mounting hardware of sufficient strength and length to secure the unit to the 
mounting surface. 

3.3 Battery Wiring 

Before connecting the batteries, please take off the DC and AC terminal covers by removing their screws. 

DC terminal bolt size: M8. 

Keep the battery bank as close as possible to the inverter.   
Follow the suggested cable length in the table below. 
 

Model 
Watt 

Battery 
Voltage 

Minimum Wire 
Gauge 

Model 
Watt 

Battery 
Voltage 

Minimum Wire 
Gauge 

0~1.0m 

1.0~5.0m 

0~1.0m 

1.0~5.0m 

12KW 

48 Vdc 

90mm²

 

120mm²

 

6KW 

48 Vdc 

45mm²

 

60mm²

 

 

Please follow the above minimum wire size requirement.   

 
One cable from the battery to the inverter is always best.    If you can’t use one cable of sufficient length, 
you may use two cables so long as the square area of both cables adds up to the recommended square of the 
minimum wire gauge.    For example, one cable of 100mm

2

 can be replaced by two cables of 50mm

2

 to 

obtain the recommended wire gauge.    When in doubt, round up and keep the cable length as short as 
possible.   
 
Battery cables must have crimped (or preferably, 
soldered and crimped) copper compression lugs 
unless aluminum mechanical lugs are used. Soldered 
connections alone are not acceptable. High quality, 
UL-listed battery cables are available. These cables 
are color-coded with pressure crimped, sealed ring 
terminals.   

 

Battery terminals must be clean to reduce the 
resistance between the DC terminal and cable 
connection. A buildup of dirt or oxidation may 
eventually lead to the cable and / or the terminal overheating during periods of high current draw. Use a stiff 
wire brush to remove all dirt and corrosion from the battery terminals and cables. 

 

Reducing RF interference 

To reduce the effect of radiated interference, twist the DC cables. To further reduce RF interference, shield 
the cables with sheathing /copper foil / braiding. 

Taping battery cables together to reduce inductance 

Do not keep the battery cables far apart. In case it is not convenient to twist the cables, keep them taped 
together to reduce their inductance. Reduced inductance of the battery cables helps to reduce induced 
voltages. This reduces ripple in the battery cables and improves performance and efficiency. 
 
CAUTION: For safety operation and regulation compliance, it’s required to install a separate DC 
over-current protector or disconnect device between battery and inverter. It may not be required to have a 

Содержание M12048D








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды