manualshive.com logo in svg

Sigineer Power M12048D, Руководство пользователя

Поделиться
Скачать
Sigineer Power M12048D Скачать руководство пользователя страница 26

                                                                                                                                            www.sigineer.com 

26 

For M Series 8-12KW models, there are two DC fans and one AC fan.   
The DC & AC fans will work together, they are designed to operate according to the following logic: 
 

Condition 

Enter Condition 

Leave Condition 

Fan Operation 

HEAT SINK TEMPERATURE 

T ≤ 40℃(104℉) 

T > 40℃(104℉) 

OFF 

T > 40℃(104℉) 

T ≤ 40℃(104℉) 

ON 

UTLITY CHARGER 
CURRENT 

I ≤ 20A 

I>20A 

OFF 

I>20A 

I ≤ 20A 

ON 

LOAD PERCENTAGE 
(INV MODE) 

20% ≤ Load 

Load>20% 

OFF 

Load>20% 

20% ≤ Load 

ON 

 
Allow at least 80CM of clearance around the inverter for air flow. Make sure that the air can circulate freely 
around the unit. 
The max fan noise level is 72db at a distance of 1m. 

 
 

2.4.10 Automatic Generator Start 

The M 6KW 12KW solar inverters are built with a very versatile 3-pin dry contact rated at 3A/250VAC on 
the rear panel. 
The internal relays of the dry contact will give out either “close” or “open” signals. 
These signals can be used to indicate the low battery voltage alarm or control a generator. 
The NC & C pins are constantly close, they will open when battery voltage reaches low alarm or the setting 
in Program 12 (DC to AC Transfer). 
The NO & C pins are constantly open, they will close when battery voltage reaches low alarm or the setting 
in Program 12 (DC to AC Transfer) to start the generator. Once the generator is started and battery voltage 
increases with charging, the dry contact pins will open at the setting of Program 13 (AC to DC Transfer) to 
avoid overcharging. 
 
Unit Status Operation 

NC & C 

NO & C 

Power Off  Inverter off ( no AC output) 

Close 

Open 

Power On  Inverter in AC Bypass Mode 

Close 

Open 

Inverter in DC to 
AC Mode 

Program 01 set 
to Utility 
Priority 

Battery Level < Low Battery 
Alarm 

Open 

Close 

Battery Level > Program 13 
(AC to DC Transfer) 

Close 

Open 

Program 01 set 
to SBU or 
Solar Priority 

Battery Level < Program 12 
(DC to AC Transfer) 

Open 

Close 

Battery Level > Program 13 
(AC to DC Transfer) 

Close 

Open 

 

For low battery alarm, when battery setting is not in “LI” mode, it is 2 volts higher than Low DC Cut-off 
Voltage for 48Vdc model and 1 volt higher than Low DC Cut-off Voltage for 24Vdc model. 

When the battery setting is in “LI” mode, low battery alarm is 5% higher than Low DC Cut-off Soc. 
 

Note: This diagram only works for certain types of generators. For your specific generator wiring, pls 
contact the generator supplier or us for wiring. 

 

Содержание M12048D








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды