manualshive.com logo in svg

SIG Award Winning Model Designs P-51D Mustang, Инструкция по сборке, Страница: 1 / 5

Поделиться
Скачать
SIG Award Winning Model Designs P-51D Mustang Скачать руководство пользователя страница 1

 

 
Your kit contains the following parts. Please check your kit for any missing or damaged parts before starting construction.

 

COMPLETE KIT PARTS LIST

1 Plan Sheet

2

Decal Sheet

2

Gray Tissue

1 1/16"x12" Landing Gear Wire

1

Tailwheel Assy.

1

Plastic Canopy

1 Plastic Spinner

11 1/16"sq.x18" Balsa Strip

22 3/32"sq.x18" Balsa Strip

4 3/32"x3/16"x18" Balsa Strip

1

3/16"x2" Birch Dowel

1

Instruction Manual

1 9" Plastic Propeller

1

Propeller Shaft

2

Brass Washer

1 Nylon Propeller Bearing

2

Plastic Wheels

2

1/16" Plastic Wheel Retainers

1 3/16"x60" Rubber Strip

1

Laser Cut Plywood Disk (N-1)

5

Laser Cut Sheets

 

Tools and Building Supplies

You will need the following items to assemble this model. You must read and follow all of the manufactures 
instructions provided with these items!

-Glue

CA, White Glue, Sigment or Ambroid all work well.

-Cutting Tools

A hobby knife with a #11 blade is used for general cutting. A single edge 
razor blade is also a useful cutting tool.

-Clear Dope, Thinner & paint brush

-320 and 400 grit sandpaper

-Straight Pins

-Wax Paper

-Needle nose pliers

-1/4" Drill Bit

-Building Board

Содержание Award Winning Model Designs P-51D Mustang






Отзывы:

Нет отзывов