manualshive.com logo in svg

SIFCO ASC TechnoPlate Power Pack 6030A20V, Руководство по эксплуатации

Поделиться
Скачать
SIFCO ASC TechnoPlate Power Pack 6030A20V Скачать руководство пользователя страница 8

 

 

SIFCOTechnoPlate Power Pack_2019-05-06_V1.5_e.doc 

 

8/68 

plating electronic GmbH      -      Rheinstraße 4     -     D-79350 Sexau      -     Germany 

Tel.: +49 (0)7641 / 93500-0   - Fax.: +49  (0) 7641 / 93500-999   E-Mail:  [email protected]

 

 

 

Security advice: 

The DC-power-supplies of the 

SIFCO TechnoPlate POWER PACK

 series 

are designed as desktop units. 

The DC power supplies are only to be operated in the permissible ranges 
of current, voltage, environmental temperature and atmospheric humidity 
according to the rating plate and the operating manual. 

The devices are only to be used in plating systems. The use of the 
device for other applications must be released by the manufacturer. 

The safety precautions must be done according to all local and federal 
regulations. 

2.3 

Installation of the DC power supply modules 

While mounting the module and the DC connectors, observe especially 
the following: 

- 

Don‘t tighten screws with a lever, don’t bent any rails or panels. 

- 

The device must be operated as desktop unit. 

- 

If mounting the device near the plating tanks or similar installations 
is necessary, one has to make sure that it is protected against 
chemical vapor, dust and dropping particles. 

- 

Ensure an unhindered airflow at the air input and air output. 

- 

Observe the installation instructions of the electrical installation. 

2.4 

Operation conditions 

Plating DC power supplies are not to be operated in an explosive 
environment. Ensure a sufficient airflow to avoid an internal overheating. 

The cooling air must be free from any chemical contamination and free 
from particles, steam and dust. 

The unit must be protected from dropping particles, dripping water and 
splash water. 

If contaminated air is getting into the device, the electronic 
components could be damaged.

 

Содержание ASC TechnoPlate Power Pack 6030A20V





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды