manualshive.com logo in svg

SIFCO ASC TechnoPlate Power Pack 6030A20V, Руководство по эксплуатации

Поделиться
Скачать
SIFCO ASC TechnoPlate Power Pack 6030A20V Скачать руководство пользователя страница 37

 

 

SIFCOTechnoPlate Power Pack_2019-05-06_V1.5_e.doc 

 

37/68 

plating electronic GmbH      -      Rheinstraße 4     -     D-79350 Sexau      -     Germany 

Tel.: +49 (0)7641 / 93500-0   - Fax.: +49  (0) 7641 / 93500-999   E-Mail:  [email protected]

 

 

 

18.2 

STORE key 

The 

STORE

 key has two functions: 

1) 

By pushing the 

STORE

 key, the display shows for 2 

sec. the loaded preset values of the actual step. 

2) 

By pushing and holding the 

STORE

 key for 2 sec. the 

actual set values (that could have been modified by 
turning the potentiometers) will be stored to the actual 
step. 

18.3 

STEP RESET key 

The 

STEP RESET

 key has two functions: 

1) 

When working with steps is it possible to do a fine 
adjustment of the set values at any time (just turn 
corresponding potentiometer). By pushing the 

STEP RESET 

button, the fine adjusted values will be set back to the step 
set values. Alternatively, the fine adjusted values can be 
directly stored on the actually used step number by using the 

STORE

 button. 

2) 

By pushing and holding the 

STEP RESET

 button for 2 sec., all 

actual parameters from the selected step will be set to zero. The 
step will not be deleted. A step can only be deleted in the step 
function menu via ENTER / Main menu / Settings / Step function). 

Содержание ASC TechnoPlate Power Pack 6030A20V





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды