SIFCO ASC TechnoPlate Power Pack 6030A20V Скачать руководство пользователя страница 36

Страница: 36 / 68

SIFCOTechnoPlate Power Pack_2019-05-06_V1.5_e.doc

36/68

plating electronic GmbH - Rheinstraße 4 - D-79350 Sexau - Germany

Tel.: +49 (0)7641 / 93500-0 - Fax.: +49 (0) 7641 / 93500-999 E-Mail: [email protected]

“Normal Operation”: A continuous potentiometer control is activated
until a step

“1” or higher will be selected. If step “Normal Operation””

is selected, the actual values are shown permanently on the display.

The factory preset parameters will be predefined by SIFCO.

The factory settings include 10 preset steps. More steps can be
predefined in the step menu.

The set values can be modified in the step modus itself or in the
step menu. The step labeling can be done in the step menu or by
actuating the “LABEL” key.

18.1

STEP and NEXT STEP keys

By pushing the “

STEP

” key, the step number is counted down

by 1.



Step 10, Step 9, 8, … “Normal Operation” (STEP “Normal Operation”

= STEP function deactivated)

By pushing the “

NEXT STEP

” key, the step number is

counted up by 1.



Normal Operation, Step 1, 2, … Step 10

There is no loop implemented!

If the

OFF

key was pressed and a STEP is selected (not “Normal

peration”), the display shows the set values as shown below

(example):

Use the potentiometers for adjustment.

Press STORE key for 3 seconds to store the new values

press STEP RESET to go back to previous values as loaded before;

press STEP RESET

for 3 seconds

to set the values to zero.

Содержание ASC TechnoPlate Power Pack 6030A20V





































































Результаты поиска

Содержание ASC TechnoPlate Power Pack 6030A20V

Отзывы:

Бренды по названию

Популярные бренды

SIFCO ASC TechnoPlate Power Pack 6030A20V, Руководство по эксплуатации

Результаты поиска

Содержание ASC TechnoPlate Power Pack 6030A20V

Отзывы:

Бренды по названию

Популярные бренды