manualshive.com logo in svg

SIFCO ASC TechnoPlate Power Pack 6030A20V, Руководство по эксплуатации

Поделиться
Скачать
SIFCO ASC TechnoPlate Power Pack 6030A20V Скачать руководство пользователя страница 35

 

 

SIFCOTechnoPlate Power Pack_2019-05-06_V1.5_e.doc 

 

35/68 

plating electronic GmbH      -      Rheinstraße 4     -     D-79350 Sexau      -     Germany 

Tel.: +49 (0)7641 / 93500-0   - Fax.: +49  (0) 7641 / 93500-999   E-Mail:  [email protected]

 

 

 

18 

Step function 

The step function is used for a fast recall of stored preset values. 

A step preset includes the following parameters: 

- 

DC voltage 

- 

DC current 

- 

Preset ampere-hour counter set value 

- 

Pole changer polarity will be shown as plus “+” or minus “-“ 
character 

- 

Labeling (step name) 

- 

Step number 

 

 

General function: 

1. 

Status: rectifier is running: 

By selecting a step, the preset parameters will be loaded and the 
rectifier output will switch directly to the new setpoints. No additional 
confirmation is needed! 

2. 

By selecting a step, the new set values will be shown on the display 
for 2 sec. After 2 sec. the display switches to the actual values. 

It is not possible to change to “Normal Operation”, or to change from 
“Normal Operation” to STEP 1 or to the following, if the ON key was 
pressed. There will be a message on the display if you try to do so. 

3. 

Status: rectifier is not running: 

4. 

By selecting a step, the preset parameters will be loaded, but the 
rectifier will just start after pushing the ON button on the control unit. 

The set values of selected step 

(except “Normal Operation”) will be 

shown continuously until the rectifier will be switch on. 

Содержание ASC TechnoPlate Power Pack 6030A20V





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды