manualshive.com logo in svg

SIFCO ASC TechnoPlate Power Pack 6030A20V, Руководство по эксплуатации

Поделиться
Скачать
SIFCO ASC TechnoPlate Power Pack 6030A20V Скачать руководство пользователя страница 27

 

 

SIFCOTechnoPlate Power Pack_2019-05-06_V1.5_e.doc 

 

27/68 

plating electronic GmbH      -      Rheinstraße 4     -     D-79350 Sexau      -     Germany 

Tel.: +49 (0)7641 / 93500-0   - Fax.: +49  (0) 7641 / 93500-999   E-Mail:  [email protected]

 

 

 

15 

Ampere-Hour Counter and Reset function 

This is the PRESET counter for alarm output and AUTO-switch-off. 

 

 

15.1 

A/H value setting (A/H PRESET) 

Press the A/H PRESET key to set the preset value (see detailed 
description in item 20.5 Preset counter). 

For other settings of the PRESET counter, please go to the SETTINGS 
menu and select the item “Preset Counter”. 

To disable the AUTO-switch-off and alarm function of the PRESET 
counter, set the value to 0.0000. The counter is counting anyway, but 
without alarm and without switching off. 

The LED in the A/H PRESET key is always off. 

15.2 

A/H RESET function 

The ampere-hour counter (= PRESET COUNTER) is directly reset to 
zero by pushing the button “A/H RESET”. No time delay, no security 
prompt! 

Consider:

 This is just a RESET function. You cannot switch the counter 

ON or OFF here! It is always running. 

The LED in the A/H RESET key is always ON. 

Содержание ASC TechnoPlate Power Pack 6030A20V





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды