manualshive.com logo in svg

Sierra Wireless WISMO Series, Руководство пользователя, Страница: 55 / 76

Поделиться
Скачать
Sierra Wireless WISMO Series Скачать руководство пользователя страница 55

 
 
 

 
 
WA_DEV_W218_UGD_004 

Rev 001 

Page 55 of 75 

WISMO Series Development Kit User 

Guide 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

9.

 

Installing the WISMO218 or the 
WISMO228 on the WMPXXX 
Development Kit 

Note:  

This section is for users who have the WMPXXX Development Kit. 

 
Both the WISMO218 and the WISMO228 can be readily used on either V20 or V21 version of the 
WMPXXX Development Kit, together with a WISMO Series Socket-Up Board. 
Setup the WMPXXX Development Kit and the WISMO Series Socket-Up Board as follows: 
 
 
 
 

 

Figure 32. WMPXXX Development Kit and WISMO Series Socket-Up Board Set-Up 

Caution: 

The ON/~OFF slide switch on the WMPXXX development kit MUST be set to the “OFF” position, 

otherwise, it will short circuit the power supply when powering ON the WISMO218 or the WISMO228 

using the tact switch, BP101 or the slide switch, SW102. 

 

UART1 with slide 

switch at “ON” 

UART1 (RS232 

interface) 

XMODEM switch set 

to “OFF” 

Power (3.2V-

4.8V) 

Audio 

RJ9 Jack 

Содержание WISMO Series













































































Отзывы:

Нет отзывов