Sierra Wireless WISMO Series Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 76

Sierra Wireless WISMO Series Скачать руководство пользователя страница 38

WA_DEV_W218_UGD_004

Page 38 of 75

WISMO Series Development Kit User

Table 8.

SIM Connector Pin Out

Pin #

Signal Name

I/O

I/O Type

Description

1

SIM-VCC

O

1V8 or 2V9

SIM

Power Supply

2

SIM-RST

O

1V8 or 2V9

SIM

Reset

3

SIM-CLK

O

1V8 or 2V9

SIM Clock

4

SIMPRES

I

2V8 max(*)

SIM Card Detect (Not used)

5

GND

Ground

6

VPP

Not

used

7

SIM-IO

I/O

1V8 or 2V9

SIM Data

8

CC8

2V8

SIMPRES signal supply (Not used)

(*)

For either 1V8 or 3V SIM cards.

The SIM interface controls both the 3V and 1.8V SIM cards.
ESD protections are available on all SIM signals.
The SIM interface of the WISMO218 and the WISMO228 could be electrically disconnected from the
SIM card connector, J400, if the soldering pads, J401 to J405, are dissociated. That is, dissociating the
four soldering pads allows for the transmission of undisturbed signals via the external connector
(J1100) to an external interface board.
By default, the SIM signals are available on its dedicated connector, J400 (J401 to J405 are soldered).

Audio

There is one AUDIO interface in the WISMO218 and the WISMO228. Use J700 (AUDIO2) in the
WISMO Series Development Kit to connect to this audio interface.
The audio connector could be disconnected from the WISMO218 or the WISMO228 when soldering
pads, J702 to J709, are dissociated. That is, having it unsoldered allows for the transmission of
undisturbed signals via the external connector (J1100) to an external interface board.
By default, AUDIO signals of the WISMO218 and the WISMO228 are available on its dedicated
connector J700 (AUDIO2) when J702 to J705 are soldered.

AUDIO1 Connector (J701)

The audio function at AUDIO1 J701 is not available.

«
...
36
37
38
39
40
...
»

Содержание WISMO Series













































































Отзывы:

Нет отзывов