Sierra Wireless AirLink FX100 Скачать руководство пользователя

Страница: 82 / 114

4112221

Rev 7.2

June 19, 2013

User Guide

Power Consumption

Figure 40. Typical Hardware Configuration for Power Consumption Measurement

The communication tester is a

CMU 200

from

Rhode & Schwartz

. This tester offers all required

GSM/GPRS

EGPRS/CDMA/WCDMA network configurations and allows a wide range of network

configurations to be set.

The

66321D

power supply is used to supply the FX Series, and it could also be used to measure the

total current drain by the device. The current measurement data is read through the GPIB connection.

Rhode & Schwartz NGSM 32/10

is used when measuring with 32V input voltage.

Note that a SIM card must be inserted during all consumption measurements.

The following table lists the recommended equipments to use for the consumption measurement.

Table 70.

List of Recommended Equipments

Device

Manufacturer

Part Number

Notes/Description

Communication Tester

Rhode & Schwartz

CMU 200

Quad Band
GSM/DCS/GPRS/EGPRS/CDMA/
WCDMA

Current measuring power
supply

Agilent

66321D

Used for DC-IN

11.5.1.2.

SIM Cards Used

Consumption measurement may be performed with either 3-Volt or 1.8-Volt SIM cards. However, all
specified consumption values are for a 3-Volt SIM card.

Caution:

The SIM card’s voltage is supplied by the FX Series power supply. Consumption measurement
results may vary depending on the SIM card.

11.5.2. Software Configuration

This section defines the software configuration for the equipment(s) used and the FX Series settings.

Содержание AirLink FX100



















































































































Результаты поиска

Содержание AirLink FX100

Отзывы:

Похожие инструкции для AirLink FX100

Бренды по названию

Популярные бренды

Sierra Wireless AirLink FX100, Руководство пользователя

Результаты поиска

Содержание AirLink FX100

Отзывы:

Похожие инструкции для AirLink FX100

Бренды по названию

Популярные бренды