Sierra Wireless AirLink FX100 Скачать руководство пользователя

Страница: 71 / 114

4112221

Rev 7.2

June 19, 2013

User Guide

Communicating with the FX Series

9.10. Main AT Commands for the FX Series

The table below lists the main AT Commands required for starting the FX Series. For other available
AT Commands, refer to documents [1] Open AT Application Framework AT Commands Interface
Guide and [2] AirPrime SL808xT and Q2698 Open AT Framework Commands Interface Guide.

Table 59.

Main AT Commands used for the FX Series

Feature/Function

AT Command

Response

Description

Check network
registration

AT+CREG?

+CREG: 0,1

The FX Series is registered on
the network.

+CREG: 0,2

The FX Series is not registered
on the network; registration attempt
is ongoing.

+CREG: 0,0

The FX Series is not registered
on the network; no registration
attempt has been made.

Enter PIN code

AT+CPIN=xxxx
(xxxx = PIN code)

PIN code accepted.

+CME ERROR: 16

Incorrect PIN code (with +CMEE =
1 mode*).

+CME ERROR: 3

PIN code already entered (with
+CMEE = 1 mode*).

Check the selected
band

AT+WMBS?

+WMBS:
<Band>,<ResetFlag>
OK

The currently selected band mode is
returned.

Switch bands

AT+WMBS=<Band>

Band switch is accepted; the FX
Series has to be reset for the change
to be effective.

AT+WMBS=<Band>,0 OK

Band switch is accepted; the FX
Series has to be reset for the change
to be effective.

AT+WMBS=<Band>,1 OK

Band switch is accepted and the
GSMS stack has been restarted.

AT+WMBS=<Band>

+CME ERROR: 3

Band selected is not allowed.

Receive a call

ATA

Answer the call.

Initiate a call

ATD<phone
number>;

(Do not forget the « ;
» at the end for
« voice » call)

Communication established.

+CME ERROR: 11

PIN code not entered (with +CMEE =
1 mode).

+CME ERROR: 3

AOC credit exceeded or
communications is already
established.

Initiate an emergency
call

ATD112;

(Do not forget the « ;
» at the end for
« voice » call)

Communications established.

Hang up

ATH

Communication has
been loss

NO CARRIER

Store the parameters
in EEPROM

AT&W

The configuration settings are stored
in EEPROM (non-volatile memory).

The command AT+CMEE=1 switches to a mode that enables a more complete error diagnostic.

Содержание AirLink FX100



















































































































Результаты поиска

Содержание AirLink FX100

Отзывы:

Похожие инструкции для AirLink FX100

Бренды по названию

Популярные бренды

Sierra Wireless AirLink FX100, Руководство пользователя

Результаты поиска

Содержание AirLink FX100

Отзывы:

Похожие инструкции для AirLink FX100

Бренды по названию

Популярные бренды