Sierra Wireless AirLink FX100 Скачать руководство пользователя

Страница: 51 / 114

4112221

Rev 7.2

June 19, 2013

User Guide

Signals and Indicators

6.3.1.

Reset Sequence

To activate the Reset sequence, the Reset signal has to be set to LOW for a minimum of 200µs. As
soon as the reset is done, the application can send the command



and the AT interface will send

an “OK” back to the application. If the application manages hardware flow control, the AT command
may be sent during the initialization phase.

Figure 28. Reset Sequence Diagram

Another solution is to use the

AT+WIND

command to get an unsolicited status from the FX Series.

Refer to documents [1] Open AT Application Framework AT Commands Interface Guide and [2]
AirPrime SL808xT and Q2698 Open AT Framework Commands Interface Guide for more information
regarding AT commands.

6.4.

LED Status Indicator

The FX Series has a red LED that indicates the current operational status of the device.

Table 41.

FX Series LED Status

FX Series State

LED Status

FX Series Status

Permanently lighted

The FX Series is switched ON, but not
registered in the network.

Flashing slowly

LED is ON for 200ms, OFF for 2s

The FX Series is switched ON and is
registered in a network (Idle mode).

Flashing rapidly

LED is ON for 200ms, OFF for
600ms

The FX Series is switched ON and is
registered in a network (Connected mode).

Very quick flash

LED is ON for 100ms, OFF for
200ms

The FX Series is switched on, and the
software downloaded is either corrupted or
non-

compatible (“BAD SOFTWARE”).

OFF

The FX Series is either switched OFF, or
the Flash LED has been disabled by the
user*.

The Flash LED can be disabled by the user when in Sleep mode in order to save power consumption. Refer to

section 9.8 Enabling/Disabling the Flash LED and documents [1] Open AT Application Framework AT Commands
Interface Guide and [2] AirPrime SL808xT and Q2698 Open AT Framework Commands Interface Guide for more
information on how to disable the Flash LED using an AT command.

Содержание AirLink FX100



















































































































Результаты поиска

Содержание AirLink FX100

Отзывы:

Похожие инструкции для AirLink FX100

Бренды по названию

Популярные бренды

Sierra Wireless AirLink FX100, Руководство пользователя

Результаты поиска

Содержание AirLink FX100

Отзывы:

Похожие инструкции для AirLink FX100

Бренды по названию

Популярные бренды