Sierra Wireless AirLink FX100 Скачать руководство пользователя

Страница: 29 / 114

4112221

Rev 7.2

June 19, 2013

User Guide

Interfaces

Refer to the following table for the pin description of the power supply connector.

Table 7.

Power Supply Connector Pin Description

Pin #

Signal

Description

GPIO25 (GPIO35 for FX100)

General purpose input/output

GPIO21

General purpose input/output

Vref

Voltage reference for the GPIOs

Reserved

GND

Ground

DC-IN

Input Supply for the FX Series (4.75V to 32V)

ON/OFF

Control pin to power OFF the FX Series

Reserved

The input voltage range (DC-IN) is from 4.75V to 32V, with a typical operating voltage of 13.2V.

The power cable is provided as part of the FX Series package.

Caution:

Pins 1, 2, 3, 4, 5, 8, 9 and 10 are low voltage interfaces. It is strictly prohibited to connect these pins
to any power supply as there is a risk of damaging the FX Series.

5.1.1.1.

General Purpose Input/Output

The FX Series has two external GPIO ports, GPIO21 and GPIO25 (GPIO35 for FX100); as well as a
voltage reference line,

Vref

sets the reference voltage of the input or output of the two GPIOs. Leaving it unconnected sets

the GPIO level at 2.3V

– 2.6V by default. It is

strongly

recommended to connect to the required

GPIOs’ output voltage (2.8V ~ 15V).

Refer to the following table for the pin description of the GPIOs.

Table 8.

GPIO Pin Description

Pin #

Signal

I/O

I/O Voltage

Description

GPIO21

I/O

Vref

General purpose input/output

GPIO25 (GPIO35 for FX100)

I/O

Vref

General purpose input/output

Vref

2.8V ~ 15V

Voltage reference for the GPIOs

Note:

It is recommended to use a

6-wire cable accessory

for easy access to these three lines. Please

refer to section 13.1 Standard Accessories for more information about the 6-wire cable accessory.

When the voltage reference,

Vref

, is not connected, if one of the GPIO output is in High state while

the other is in Low state, the GPIO in high level voltage will be at 2.3V.To avoid this voltage drop, it
is recommended to use

Vref

to the desired output voltage.

Содержание AirLink FX100



















































































































Результаты поиска

Содержание AirLink FX100

Отзывы:

Похожие инструкции для AirLink FX100

Бренды по названию

Популярные бренды

Sierra Wireless AirLink FX100, Руководство пользователя

Результаты поиска

Содержание AirLink FX100

Отзывы:

Похожие инструкции для AirLink FX100

Бренды по названию

Популярные бренды