Siemens VersiCharge AC Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 52

background image

2.2 Stud Mounting – Recommended (Use center-top and bottom holes)

Figure 1. Align mounting bracket and screw into the stud

NOTE:

For installation, the mounting-bracket hinges will be pointing to the ceiling, and the flat side of the

bracket will be against the wall.

1. Locate a stud within the wall that can handle the 17+ lb. load of the VersiCharge.

2. Place the mounting bracket not more than 12” above a 240 V outlet; level the mounting bracket and drill the

center-top hole using a drill with an extender.

3. Mount the bracket using the top hole and the lag screws, DO NOT tighten all the way.

4. Level the bracket

5. Drill a pilot hole for the center-bottom hole.

6. Secure with lag screws.

7. Tighten top and bottom screws securely using an Allen wrench.

• For concrete cinder block walls, install appropriate anchors. If using an existing outlet, ensure that power cord

will reach to the outlet. Using a 7/16” socket, attach mounting bracket to the wall in compliance with all National

Electrical Code® (NEC) and local jurisdiction requirements, using the 2 lag screws provided.

• For Siemens Post installation, see the post instruction manual at: (usa.siemens.com/versicharge)

12

VersiCharge™ AC Electric vehicle charging station

«
...
9
10
11
12
13
...
»

Содержание VersiCharge AC





















































Отзывы:

Нет отзывов

Похожие инструкции для VersiCharge AC

Бренд: Camcar Страницы: 2

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 88

Бренд: Samsung Страницы: 215

Бренд: Daihatsu Страницы: 43

Бренд: A&D Страницы: 35

Бренд: HAI Страницы: 2

Бренд: PASCO Страницы: 3

witty park XEV6 Series

Бренд: hager Страницы: 9

Бренд: Kathrein Страницы: 52

Бренд: Oki Страницы: 8

Бренд: Oki Страницы: 51

Бренд: Tait Страницы: 10

Powersaver Dual Flexi

Бренд: Sangamo Страницы: 2

Бренд: Waterpik Страницы: 28

Бренд: Waterpik Страницы: 2

Water Flosser WF-03

Бренд: Waterpik Страницы: 2

Бренд: Waterpik Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды