Siemens VDO DTCO 1381 Скачать руководство пользователя страница 135

Страница: 135 / 302

Service only

Installation

5.5 Performing the installation

Edition 07/2007

Technical Description DTCO 1381

5 - 31

TD00.1381.00 13

2 102

5.5.8 Mounting the DTCO 1381

Fig. 5 - 18: Mounting the DTCO 1381 in the radio compartment

On the rear of the DTCO 1381

(2)

press the mounting cap

(5)

onto the spacer

(3)

or the threaded bolt

(4)

Then push the DTCO 1381 into the mounting frame

(1)

until it

engages in the frame and the cover is flush with the console.

There is usually a mounting bracket with a hole

(6)

on the rear wall

of the radio compartment. When the DTCO 1381 is pushed in, the
fastening cap

(5)

locks into this hole.

Attention!

When inserting the DTCO 1381 into the installation frame, make
sure that none of the cables become pinched and damaged!

Содержание VDO DTCO 1381













































































































































































































































































































Результаты поиска

Содержание VDO DTCO 1381

Отзывы:

Бренды по названию

Популярные бренды

Siemens VDO DTCO 1381, Техническое описание

Результаты поиска

Содержание VDO DTCO 1381

Отзывы:

Бренды по названию

Популярные бренды