Siemens TX-I/O Скачать руководство пользователя | Manualshive

Страница: 60 / 94

background image

60 / 94

Siemens

TX-I/O PROFINET BIM V1.0

CM110564en_02

Building Technologies

Parameters

23.09.2010

The minimum pulse times are defined by, among other factors, the hysteresis [Hys]
properties. Where:

Minimum pulse length for OnCmd = [Hys]



[RiseTime]

Minimum pulse length for OffCmd = [Hys]



[FallTime]

Value range

Unit

0...20 %2

4.12.13 Enabling Local Override

The local override function for the channel is enabled by pressing the rocker switch
of a channel. The following assignments apply in this case.
Pressure on…



...

middle

(hand): local override ON /

OFF; no

change at the output. The yellow
LED of the channel lights while the
override function is switched on



... + (up):

connected device on; I/O point (n)



... – (down):

connected device off; I/O point (n+1)

The

stroke algorithm

is updated when the local override function is activated.

The local override function can be disabled in the configuration.

The TXM1.6R-M module enables local override. Press the rocker switch of

either

of the two channels. The following applies: pressure on…

4.12.14 Local Override Mode

Parameter for defining the type of 'local override' signal.

A logical '1' is usually interpreted as 'active'. However, it is possible for migrations
to interpret a logical '0' as 'active'.

The following assignments apply here:

Value

Input

Local override

Active 1

Active

Inactive 0 Active
Active 0

Inactive

Inactive 1 Inactive

4.12.15 Process Data

The allocation of process data and the channel status information of analog output-
configured channels for local override are described in 'Process Data Channel
Mapping' for the corresponding TX-I/O module.

If local override is active after starting the TX-I/O, [StrokeModel] is set to the value
of the last override value. As a result, the relay remains inactive and the drive is
immobile.

If the TX-I/O BIM is in the status 'Masterdown', the backup function becomes active.
The backup function works in the mode defined by [BackupMode].

Hysteresis

Manual operation

Definition,

addition

Local override

Masterdown

«
...
58
59
60
61
62
...
»

Содержание TX-I/O































































































Отзывы:

Нет отзывов

Похожие инструкции для TX-I/O

PACSystems RX7i

Бренд: GE Страницы: 317

Бренд: PACH & COMPANY Страницы: 4

Бренд: Quantum Страницы: 97

Бренд: TCS Страницы: 16

Бренд: Teac Страницы: 3

digital slim -1400

Бренд: Fisher Страницы: 20

Бренд: ShoreStation Страницы: 15

BLUEBOX ADVANT UHF

Бренд: iDTRONIC Страницы: 54

Бренд: B&B Molders Страницы: 18

Бренд: Fagor Страницы: 68

UniFi Protect UVC-G4-Doorbell

Бренд: Ubiquiti Страницы: 24

Бренд: NEC Display Solutions Страницы: 4

Бренд: Ezon Страницы: 9

Бренд: XtendLan Страницы: 14

Safeline DNSL-IO2

Бренд: DINA Страницы: 28

Бренд: Jensen Страницы: 20

Бренд: Haklift Страницы: 32

JFLEX-Visualisation1

Бренд: Kontron Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды