Siemens TX-I/O Скачать руководство пользователя

Страница: 59 / 94

59 / 94

Siemens

TX-I/O PROFINET BIM V1.0

CM110564en_02

Building Technologies

Parameters

23.09.2010

4.12.9 FallTime

Parameter for defining the close time of a valve, flap, etc.

Value range

Unit

Recommended range

63...65535 0.1

6.5...600 s

The fall time (100% to 0 %) can be defined within the range specified above.

4.12.10 BreakTime

Parameter for defining the break time (pause) when a drive changes direction
(open/close).

Value range

Unit

0...255 0.1

4.12.11 NeutralZone

Parameter for setting the percentage share of the extent of a neutral zone (in
relationship to the required time).

Value range

Unit

0...20 0.1

Is the difference between the process value and path algorithm greater than half of
the neutral zone plus hysterisis, a pulse of appropriate length and direction is
generated until the difference value is again within the neutral zone.

4.12.12 Hysteresis

(Switching Limit)

Parameter for defining the component of deviation between [StrokeModel] and the
process value [AOVal].

The process value must be reached until the [StrokeModel] has been adjusted and,
as a result, an OnCmd or OffCmd pulse has been generated..

The entire deviation



ctr

in the figure below must comply with the following

condition:



















Hysteresis

NeutralZon

ctr

Definition,

addition

Definition,

addition

Definition,

addition

Function

Definition,

addition

Содержание TX-I/O































































































Результаты поиска

Содержание TX-I/O

Отзывы:

Похожие инструкции для TX-I/O

Бренды по названию

Популярные бренды

Siemens TX-I/O, Руководство пользователя

Результаты поиска

Содержание TX-I/O

Отзывы:

Похожие инструкции для TX-I/O

Бренды по названию

Популярные бренды