Siemens TX-I/O Скачать руководство пользователя

Страница: 53 / 94

53 / 94

Siemens

TX-I/O PROFINET BIM V1.0

CM110564en_02

Building Technologies

Parameters

23.09.2010

4.11 Analog Output (Positioning)

AO_U10N, AO_I420N

(SIMATIC Manager hardware catalog)

Parameter for changing/mapping the process value [AOValue] as a SIMATIC
standard analog value.

4.11.1 Functions

DC voltage output.

Voltage measurement

SIMATIC HW
catalog

Description

Rated output range Maximum output

range

Resolution

AI_U10N

DC voltage output 0…10 V



0.054 V…



10.66 V

DC current output.

Voltage measurement

SIMATIC HW
catalog

Description

Rated
measurement
range

Maximum
measurement
range

Resolution

AI_U10N

DC output

4…20 mA

16/10000 mA

4.11.2 Backup Mode

Function for control of the behavior of the function when changing to the
'MasterDown' status.

Possible values

Description

Process value = INACTIVE, 0 (Off)

VALUE

Specific value of the parameter [BOBackupValue]

KEEP

Save the last active process value

4.11.3 AO Backup Value

Parameter – type [AnalogValueEnum] – that represents the backup value and
becomes valid in the following cases:



a change in status to 'MasterDown'

and



the parameter [BackupMode] = VALUE

Value range

-32768 .. +32767

Representation

Definition,

addition

AO_U10N

AO_I420N

Definition,

addition

Definition,

addition

Содержание TX-I/O































































































Результаты поиска

Содержание TX-I/O

Отзывы:

Похожие инструкции для TX-I/O

Бренды по названию

Популярные бренды

Siemens TX-I/O, Руководство пользователя

Результаты поиска

Содержание TX-I/O

Отзывы:

Похожие инструкции для TX-I/O

Бренды по названию

Популярные бренды