Siemens Synco living Скачать руководство пользователя страница 55

Страница: 55 / 100

55 / 100

Siemens

Synco™ living Operating instructions

CE1B2707en

Building Technologies

Central apartment unit QAX910

23.08.2008

Forced DHW charging

With a long push on the central apartment unit’s

DHW

button,

one-time forced charging of the DHW storage tank to the Normal
setpoint is triggered. During the time forced charging is active, the
DHW symbol on the display flashes

Manual forced charging of the DHW storage tank can also be triggered via the
following operating line:

Main menu > DHW > Operating mode > Forced charging man:

State of DHW operating mode

The present state of the DHW operating mode can be displayed (Auto, Nor-
mal, Reduced, Protection).

Main menu > DHW > Operating mode > State:

Reason for DHW operating mode

If the current DHW operating mode does not satisfy your needs, the reason for
the operating mode can be displayed:

Main menu > DHW > Operating mode > Cause

Possible reasons for the current operating state:

•

Commissioning

•

Electrical heating

•

Forced charging

•

DHW charging lock

•

Legionella program

•

DHW operating mode (if not “Auto“)

•

Special day / holidays / absence

•

DHW time switch

•

Summer operation

DHW operating mode during absence

The DHW operating mode required during absence can be selected:

Main menu > DHW > Operating mode > Optg mode absence:

Factory setting

---

Your setting

--- (no impact, according to time program)

Normal

Reduced

Protection

Содержание Synco living





































































































Результаты поиска

Содержание Synco living

Отзывы:

Похожие инструкции для Synco living

Бренды по названию

Популярные бренды

Siemens Synco living, Руководство по эксплуатации

Результаты поиска

Содержание Synco living

Отзывы:

Похожие инструкции для Synco living

Бренды по названию

Популярные бренды