manualshive.com logo in svg

Siemens ST950, Руководство пользователя

Поделиться
Скачать
Siemens ST950 Скачать руководство пользователя страница 122

 

ST950 Plus+ User Manual 

 

  

 

 

ST950 Plus+ User Manual 

Page 122 of 176 

667/HE/53000/000   

Issue 2 

Unrestricted 

 

 

 

Figure 62 - Licence Manager web page with external reader fitted 

 

The 

Currently  Installed  Licences

  table  shows  the  licences  currently  installed  in  the  controller 

(contained in the Licence Smart Card fitted to the controller CPU Card). The example above shows 
that the controller currently has two licences installed: Remote Access and a combined OTU & 
MOVA licence. Each installed licence has an associated 'Uninstall' button which can be used to 
transfer the licence from the controller to the Licence Smart Card in the external USB Smart Card 
reader.  Pressing  this  button  results  in  the  licence  being  removed  from  the 

Currently  Installed 

Licences

 table and added to the 

Plug-in Card Reader

 table and the facility becoming unlicensed. 

The 

Plug-In Card Reader

 table shows the licences contained in the Licence Smart Card fitted in the 

external USB Smart Card Reader. This Licence Smart Card holds a number of licences. Any of these 
can be transferred to the controller by pressing the 

Install

 button associated with the licence. As 

the controller already has a Remote Access licence fitted, transferring this licence to the controller 
would not enable any additional facilities (it would just end up with two of the  same licence). 
Transferring a LwTunnel licence to the controller would activate the lightweight tunnel facility. 

When a licence is installed, it is removed from the list of licences held on the Licence Smart Card 
in the external USB Smart Card reader and added to the list of currently installed licences. Once a 
licence has been installed, the associated facility can be operated without restriction. 

6.9.8

 

Network Connection 

The  configuration  required  depends  upon  the  network  in  which  the  controller  resides.  Two 
straightforward cases are described below each corresponding to the controller being connected 
to a single system: Stratos (section 6.9.9) & a non-Stratos system e.g. UTC (section 6.9.10). Where 
the controller is to be connected to more than one system, the network will have to be designed 
and the controller configured accordingly using a combination of the two methods as appropriate. 

Содержание ST950



















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды