Siemens ST950 Скачать руководство пользователя страница 104

Страница: 104 / 178

ST950 Plus+ User Manual

Page 104 of 176

667/HE/53000/000

Issue 2

Unrestricted

Installation of Stool

The Plus

Controller can be mounted on one of three different stools.

For all relevant stool installation methods please refer to 667/CC/53060/000

–

Siemens Mobility

Controller Cabinet Stool Installation Method Statement.

Installation of Traffic Signal Poles.

The installation of the street infrastructure is outlined in the following documents;

667/HE/20662/000 Installation & Commissioning

–

Signals & Poles

Site Cable Installation

Site Cable Installation

For all site cabling to be installed, the installer is to refer to the Plus+ STS drawing, site layout

design and configuration documentation. The STS drawing will contain

all cable routes,

connection details and street furniture locations.

The design tool and the Plus

Site Layout design has been developed such that it meets the

standards as set out in 667/DS/20664/048 - Traffic Signal Junction Cable Design & Certification for
ELV Systems.

In addition, the installer should confirm that the Plus

Site Layout version provided matches that

identified on the Completion Certificate.

Traffic Signal Installation Completion Certificate (667/HE/20664/004)

Prior to installation please confirm that the junction design engineer has completed the first

part and the second half as verification that the electrical design, including junction cabling,

is as required in Junction Cabling Design Guide.

If the installers have deviated from the Plus+ Layout Design (see next point), the installers

must sign off the second part to confirm the installation continues to meet regulations.

Additionally, ensure that the Site Layout Drawing Number and Revision are recorded on the

certificate.

Содержание ST950



















































































































































































Результаты поиска

Содержание ST950

Отзывы:

Бренды по названию

Популярные бренды

Siemens ST950, Руководство пользователя

Результаты поиска

Содержание ST950

Отзывы:

Бренды по названию

Популярные бренды