background image

en

    Operating the appliance

22

End of programme

The programme has ended when the 
End display 

)"

 is lit.

Note

To save energy, the dishwasher 
automatically switches off after 
2 minutes after 
the end of the programme.

Switching off the appliance

Short time after the end of the 
programme:

1.

Switch off ON/OFF switch 

(

.

2.

Turn off the tap (not applicable if 
Aqua-Stop fitted).

3.

Remove the utensils when they have 
cooled down.

Note

When the programme ends, leave 
the appliance to cool down a while 
before opening it. This will prevent 
steam from escaping and causing long-
term damage to your built-in furniture.

Interrupting the programme

1.

Switch off ON/OFF switch 

(

.

The LEDs go out. The programme is 
saved. 
If the door was opened on an 
appliance which has a warm water 
connection or is heated, first leave 
the door ajar for several minutes and 
then close. Otherwise, expansion 
(pressure) may cause the appliance 
door to spring open or water to run 
out of the appliance.

2.

To continue the programme, switch 
on the ON/OFF switch 

(

 again.

Terminating the programme

Terminating the programme 

(Reset)

1.

Press START button 

@

 for approx. 

3 sec.
The End display 

)"

 is lit.

2.

The remaining programme sequence 
lasts approx. 1 minute.
Switch off ON/OFF switch 

(

.

Changing the programme

When the START button 

@

 has been 

pressed, the programme cannot be 
changed.
The only way a programme can be 
changed is by Cancel programme 
(Reset).

Intensive drying

The final rinse uses a higher 
temperature which improves the drying 
result. The running time may increase 
slightly. (Caution if utensils are delicate!)

1.

Close the door.

2.

Switch on ON/OFF switch 

(

The Cleaning display 

)*

 flashes.

3.

Press and hold down the START 
button 

@

.

4.

Rotate programme selector 

8

 until 

the “Check water supply” display 

h

 flashes.

5.

Release button.

To change the setting:
1.

By rotating the programme selector 

8

, you can switch on intensive 

drying (End display 

)"

 

is lit) or switch off intensive drying 
(End display 

)"

 is not lit).

2.

Press START button 

@

.

The setting is saved.

Содержание SR series







































Отзывы: