Siemens SIWAREX WP251 Скачать руководство пользователя страница 92

Страница: 92 / 220

Scale parameters and functions

8.8 DR 7 Process interfaces

SIWAREX WP251

Manual, 12/2015, A5E37203357A

8.8.5

Response of digital outputs to faults or SIMATIC STOP

This parameter allows you to define the response of the digital outputs following a fault of the

SIWAREX module or SIMATIC STOP.

Function

code

Response

0 (default) Outputs are switched off
1

Outputs are not switched off (continue)

The relevant substitute value is activated

Outputs are switched on

8.8.6

Substitute value for DQ 0, 1, 2, 3 following fault or SIMATIC STOP

The outputs are usually reset following a module fault (operating error) or SIMATIC CPU

STOP. This response is the default setting.
If an output is to be set following a fault, this response is defined using this parameter. The

"Response of digital outputs to fault or SIMATIC STOP" parameter must also be set to

"Output substitute value".

Examples

Table 8- 6

Bit 0 defines digital output 0 (DQ 0)

Value of bit 0

Value of DQ 0 following fault

0 (default)

Table 8- 7

Bit 1 defines digital output 2 (DQ 2)

Value of bit 2

Value of DQ 2 following fault

0 (default)

NOTICE
Risk to the plant
If an output is set following a fault (operating error), this can pose a risk for the plant.
Ensure that the parameters are correctly set.

Содержание SIWAREX WP251





























































































































































































































Результаты поиска

Содержание SIWAREX WP251

Отзывы:

Бренды по названию

Популярные бренды

Siemens SIWAREX WP251, Руководство пользователя

Результаты поиска

Содержание SIWAREX WP251

Отзывы:

Бренды по названию

Популярные бренды