manualshive.com logo in svg

Siemens SIWAREX WP251, Руководство пользователя

Поделиться
Скачать
Siemens SIWAREX WP251 Скачать руководство пользователя страница 82

Scale parameters and functions 

 

8.7 DR 6 Limits 

 

SIWAREX WP251 

82

 

Manual, 12/2015, A5E37203357A 

8.6.4

 

Zero by power-on (value when switching on) 

If the automatic zero by power-on is configured, the scale is automatically set to "Zero" when 

the power supply is switched on provided the gross weight is within the defined zero setting 

limits. The current gross weight is saved as the zero by power-on weight. The zero by 

power-on weight must be within the specified range (usually ± 10 %). 

8.6.5

 

Zero weight (semi-automatic) 

The zero weight command (see command 1001) entered by the user sets the current gross 

weight to "Zero" provided it is within the defined zero setting limits. The current gross weight 

is saved as the zero weight. The zeroing weight must be within the specified range (usually 

+3 / -1 % of the set zero point). 

8.6.6

 

Current zero tracking weight 

The current zero tracking weight is recorded in this parameter if automatic zero tracking is 

activated. 

8.6.7

 

Dead load 

The characteristic curve of the scales is determined during calibration. When there is no 

load, the main display returns "0". The dead load is the weight of the empty scales, i.e. the 

weight of the scales themselves. 

8.7

 

DR 6 Limits 

8.7.1

 

Overview 

The switch-on and switch-off values for Limits 1, 2 and 3 are configured in data record DR 6. 
In legal trade operation, the data record is not write-protected. 

Table 8- 4 

Assignment of data record 6 

Variable 

Note 

Type 

Length 

(bytes) 

Rw 

Default 

Min. 

Max. 

Modbus 
Register 

Data record number

 

Contains no. of the 

data record

 

USHORT

 

2

 

r

 

6

 

 -

 

 -

 

1234

 

Length

 

Data record length 

information

 

USHORT

 

2

 

r

 

60

 

 -

 

 -

 

1235

 

Содержание SIWAREX WP251





























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды