manualshive.com logo in svg

Siemens SIWAREX WP251, Руководство пользователя

Поделиться
Скачать
Siemens SIWAREX WP251 Скачать руководство пользователя страница 61

Scale parameters and functions 

8.3 DR 3 Calibration parameters 

SIWAREX WP251 
Manual, 12/2015, A5E37203357A 

61

 

7. Scale is emptied, if necessary (based on setting in DR 25) (weighing step 5)
8. WP251 jumps to weighing step 0 and waits for further commands or jumps directly back

to step 1 (continuous operation).

8.2.6

 

Operating mode A

WI

 (automatic catchweighing instrument) - Removal 

In ACI mode, WP251 allows a set point to be set, which is then dosed automatically by the 

dosing functionality of the module.  
The dosing signals "Coarse flow/Fine flow" can be used to directly control the corresponding 

dosing elements (e.g. valves). After the set point is reached, WP251 automatically logs the 

dosed weight in the log memory and completes the weighing operation autonomously. 
In contrast to NAWI mode, the logging of the dosed single weight is written automatically to 

the log memory without an operator intervention.  
"Removal" means that the product to be weighed is dosed from the scale (for example, a silo 

on load cells with discharge valves). In this case, the full scale is tared and the net weight 

increases with decreasing gross weight. The "Dosing start" parameter in DR 25 should be 

set to "Tare" for correct operation. 
Dosing in continuous operation is possible. 
Here is the basic sequence of dosing in ACI - Removal mode: 
1. Scale is filled with sufficient material.
2. PLC sends set point (DR 20) and material parameters (DR 23) to WP251
3. PLC sends "Start" command (e.g. 1101) to WP251
4. WP251 tares (based on setting in DR 25) (weighing step 1)
5. Coarse/fine dosing phase starts (weighing step 2)
6. If configured and necessary, post-dosing occurs (DR 22) (weighing step 3)
7. Dosing result is automatically checked and logged (weighing step 4)
8. Emptying signal is set, if necessary (based on setting in DR 25) (weighing step 5)
9. WP251 jumps to weighing step 0 and waits for further commands or jumps directly back

to step 1 (continuous operation).

8.3

 

DR 3 Calibration parameters 

8.3.1

 

Overview 

The calibration parameters (DR 3) must be checked and changed, if necessary, for each 

scale. 

Содержание SIWAREX WP251





























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды