Siemens SIWAREX WP251 Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 220

Siemens SIWAREX WP251 Скачать руководство пользователя страница 60

Scale parameters and functions
8.2 Weighing steps

SIWAREX WP251

60

Manual, 12/2015, A5E37203357A

completes the weighing operation autonomously. Optionally, WP251 can also empty the

scale.
In this operating mode, the dosing is controlled by WP251 in a fully-automatic operation. In

contrast to a NAWI scale, logging of the individual dosings by an operator command is not

required (WP251 logs every weighing nevertheless). The scale is therefore tested during

verification to see if the set point setting is always within the legally prescribed limits.
Typically, AWI scales dose continuously in continuous operation, which WP251 also

supports. In this operating mode, the option also exists to define cycles that are not

zeroed/tared and not checked. This increases the throughput of the scale because the

operations that require a standstill do not occur in every cycle.
In practice, the execution of dosing in AWI mode can be as follows:
1. PLC sends set point (DR 20) and material parameters (DR 23) to WP251
2. PLC sends "Start" command (e.g. 1101) to WP251
3. WP251 performs zero setting or tares (based on setting in DR 25) (weighing step 1)
4. Coarse/fine dosing phase starts (weighing step 2)
5. If configured and necessary, post-dosing occurs (DR 22) (weighing step 3)
6. Dosing result is automatically checked and logged (weighing step 4)
7. Scale is emptied, if necessary (based on setting in DR 25) (weighing step 5)
8. WP251 jumps to weighing step 0 and waits for further commands or jumps directly back

to step 1 (continuous operation).

8.2.5

Operating mode A

WI

(automatic catchweighing instrument) - Filling

In ACI mode, WP251 allows a set point to be set, which is then dosed automatically by the

dosing functionality of the module.
The dosing signals "Coarse flow/Fine flow" can be used to directly control the corresponding

dosing elements (e.g. valves). After the set point is reached, WP251 automatically logs the

dosed weight in the log memory, performs a tolerance check, corrects the shut-off points of

the dosing signals if necessary and completes the weighing operation autonomously.

Optionally, WP251 can also empty the scale.
In contrast to NAWI mode, the logging of the dosed single weight is written automatically to

the log memory without an operator intervention.
Dosing in continuous operation is possible.
Here is the basic sequence of dosing in ACI Filling mode:
1. PLC sends set point (DR 20) and material parameters (DR 23) to WP251
2. PLC sends "Start" command (e.g. 1101) to WP251
3. WP251 performs zero setting or tares (based on setting in DR 25) (weighing step 1)
4. Coarse/fine dosing phase starts (weighing step 2)
5. If configured and necessary, post-dosing occurs (DR 22) (weighing step 3)
6. Dosing result is automatically checked and logged (weighing step 4)

«
...
58
59
60
61
62
...
»

Содержание SIWAREX WP251





























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды