manualshive.com logo in svg

Siemens SIWAREX WP251, Руководство пользователя

Поделиться
Скачать
Siemens SIWAREX WP251 Скачать руководство пользователя страница 52

Commissioning 

 

7.5 Service with the SIWATOOL program 

 

SIWAREX WP251 

52

 

Manual, 12/2015, A5E37203357A 

In order to archive data, all data can be exported from the SIWAREX module and saved as a 

file or printed. 

 

 

Note 
You can edit all data in the SIWAREX module in online mode. The changes are not 

automatically imported into the corresponding scale data block in the SIMATIC CPU. This 

data synchronization must then be started in the CPU using the corresponding command 
To download the data to the SIWAREX module, select the data record with a right mouse 

click and send it explicitly to the SIWAREX module. 

 

Online parameter trends can be recorded and played back using the recorder function 

located at the top right-hand edge of SIWATOOL. You can use the "Configure recorder" 

button to select the data records to be recorded and to set the save parameters. The 

playback speed can be set using a slider. 

7.5.6

 

Entering parameters with SIWATOOL 

There is a defined procedure for handling parameters. The current parameters in the 

SIWAREX module are displayed in the right-hand window, while the parameter values on the 

PC are displayed in the left-hand window. The new parameter value is entered first in the 

left-hand window. If several parameters of the data record are to be changed, they are 

entered consecutively. The data record is subsequently selected in the tree view and sent to 

the SIWAREX modules using the right mouse button. 
Parameters are always changed as complete data records, rather than individually. 

7.5.7

 

Recording scale traces 

Scale traces can be recorded and exported using SIWATOOL. The recording is started and 

stopped using commands, and recorded traces can also be deleted. The trace recording 

cycle is set in data record DR7. The "Export trace data" button opens a dialog window. The 

trace is displayed in this window as a table or graphic, and the data can be exported to csv 

or Excel and then processed further. The commands for starting and stopping are present in 

the "Trace commands" group (yellow memory card icon) in SIWATOOL. 
All important measured values, messages and changes in status are recorded. 

Содержание SIWAREX WP251





























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды