manualshive.com logo in svg

Siemens SIWAREX WP251, Руководство пользователя

Поделиться
Скачать
Siemens SIWAREX WP251 Скачать руководство пользователя страница 50

Commissioning 

 

7.5 Service with the SIWATOOL program 

 

SIWAREX WP251 

50

 

Manual, 12/2015, A5E37203357A 

 

Image 7-6 

Sending/receiving a data record in SIWATOOL V7 

7.5.3

 

Offline parameter assignment 

All scale parameters can be edited and saved without an electronic weighing system.  
This reduces the setup time. You can thus prepare the parameters for several scales in your 

office, and subsequently transfer them to the electronic weighing system during setup. 
Data from one scale currently in operation can be exported and used to set up another scale. 

7.5.4

 

IP address for SIWAREX 

7.5.4.1

 

Introduction 

The factory-set IP address is 192.168.0.21. This address is also preset in SIWATOOL. The 

connection to a SIWAREX module can be established immediately. The network card used 

must be configured for this network. 
If the connection is to be established to a specific SIWAREX module, its IP address must be 

set in SIWATOOL. The setting is made in menu item "Communication/Define Network 

Settings...". 
If the IP address of a SIWAREX module is unknown, it can be determined using the 

additional program "Primary Setup Tool". The program is included in the SIWAREX 

configuration package.  
During the setup, a new IP address can be assigned to the module using SIWATOOL. 
The assignment of a new IP address to a SIWAREX module is necessary if several 

SIWAREX modules are present in one network. 
The following ports are used by SIWAREX: 

●

 

SIWATOOL port: 23006 

●

 

MODBUS TCP/IP port: 502 

●

 

TFTP for firmware download port: 69 

Содержание SIWAREX WP251





























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды