manualshive.com logo in svg

Siemens SIWAREX WP251, Руководство пользователя

Поделиться
Скачать
Siemens SIWAREX WP251 Скачать руководство пользователя страница 47

 

Commissioning 

 

7.4 Quick calibration with calibration weights and SIWATOOL 

SIWAREX WP251 
Manual, 12/2015, A5E37203357A 

47

 

different offline parameters will be sent to the scale and overwrite previously active and 

intentionally defined parameters. 
You must subsequently enter the required parameters in data record DR 10 and send these 

to the module. 

 

Image 7-4 

Sending/receiving a data record / in SIWATOOL V7 

●

 

No. of mechanical support points 

 If WP251 is connected, for example, to a platform weighing machine in which the 

platform is mounted on four load cells, the number of mechanical support points if 4. 

 If it is connected to a tank that is mounted on one load cell and two fixed point 

mountings, there are 3 mechanical support points. 

●

 

Characteristic value of a load cell in mV/V, or the mean value of the characteristic values 

if there is more than one load cell 

●

 

Rated load of a load cell 

●

 

Load cell manufacturer 

 The manufacturer of the installed load cells can be quickly and easily identified in a 

service case. 

●

 

Load cell order number 

 The order number of the installed load cells can be quickly and easily identified in a 

service case. 

7.4.5

 

Calibration 

●

 

Provided that the calibration weight 0 was specified with 0 (typical case), the scale must 

now be empty (only mechanical dead load). 

●

 

Activate the "Set Calibration Point 0" (60) command. 

 

→The weight display should now indicate 0.

 

●

 

Place the previously defined "Calibration weight 1" on the scale 

●

 

Activate the "Set Calibration Point 1" (61) command. 

 

→ The calibration weight 1 should be displayed in the weight display.

 

●

 

Optional: Place the previously defined "Calibration weight 2" on the scale 

●

 

Activate the "Set Calibration Point 2" (62) command. 

 

→ The calibration weight 2 should be displayed in the weight display.

 

Содержание SIWAREX WP251





























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды