manualshive.com logo in svg

Siemens SIWAREX WP251, Руководство пользователя

Поделиться
Скачать
Siemens SIWAREX WP251 Скачать руководство пользователя страница 31

 

Connection 

 

6.4 Shield connection 

SIWAREX WP251 
Manual, 12/2015, A5E37203357A 

31

 

3.

 

Twisted wire pairs that are also shielded are required for the specified cables: 
–

 

Sensor cable (+) and (-) 

–

 

Measuring voltage cable (+) and (-) 

–

 

Supply voltage cable (+) and (-) 

 

Image 6-2 

Shielding in the screw gland 

We recommended that you use the cables listed in chapter 

→

 Accessory (Page 213). 

4.

 

The shield must be connected to ground directly in the vicinity of the SIWAREX WP251. 

The maximum distance between the SIWAREX WP251 and the load cell applies when 

using the recommended cables. 

Table 6- 2 

Load cell connections on the module 

Labeling 

Function 

Sig- 

Measurement cable load cell - 

Sig+ 

Measurement cable load cell - 

Sen- 

Sensor cable load cell - 

Sen+ 

Sensor cable load cell + 

Exc- 

Supply load cell - 

Exc+ 

Supply load cell + 

6.4

 

Shield connection 

Make sure you observe the correct design of the shield support for the shielded cables. It is 

the only way to ensure immunity of the system.  
A cable is shielded to attenuate the effects of magnetic, electrical and electromagnetic 

interference on the cable. Interference currents on cable shielding are diverted to ground by 

conductive isolation rails. To avoid interference as a result of these currents, it is imperative 

to provide a low-impedance connection to the ground. 
Use only cables with protective braided shield (see recommended cables of digital load cells 

in chapter Accessory (Page 213)). Shielding density must be at least 80%. 

Содержание SIWAREX WP251





























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды