manualshive.com logo in svg

Siemens SIWAREX WP251, Руководство пользователя

Поделиться
Скачать
Siemens SIWAREX WP251 Скачать руководство пользователя страница 21

 

SIWAREX WP251 
Manual, 12/2015, A5E37203357A 

21

 

 

Application planning 

4 

4.1

 

Functions 

SIWAREX WP251 controls complex dosing and filling processes completely autonomously. 

The four digital outputs of the module can be used to directly control the dosing elements 

(coarse and fine flow). Maximum accuracy is achieved since the weighing process is fully 

independent of the CPU and its cycle time. The CPU can be used to manage recipes and 

material parameters. These parameters and the desired set point are then transferred to 

WP251 via a function block, and the dosing process is started. SIWAREX WP251 

automatically optimizes the shut-off points, generates statistics, and logs every dosing 

operation in the internal log memory, which is also accessible from the CPU and can be read 

by the CPU. Various options are available for commissioning. The WP251 function block 

enables full access to all parameters of the WP251. The free, downloadable example 

application "Ready-for-use" enables complete commissioning, calibration and operation of 

the scale from the touch panel - without any programming needed. 
Furthermore, commissioning can be carried out with SIWATOOL V7, the PC service 

software that communicates with the SIWAREX module via Ethernet. This enables access 

via W-LAN when a WIFI access point is used. Remote access via the Internet is also 

possible problem-free. Centralized access to all scales from a single location is possible for 

servicing purposes – worldwide. 
In addition, there is full access to all parameters and commands, both via the RS485 port 

(Modbus RTU) and via the Ethernet interface (Modbus TCP/IP), meaning that full 

commissioning and operation can also take place via these channels.  
Stand-alone operation allows the module to be operated autonomously even without a 

SIMATIC CPU. For this purpose, an HMI device can be connected directly to the Ethernet or 

RS485 port of the WP251. The HMI device then communicates with the weighing module via 

Modbus TCP/IP or RTU. This setup can also be selected to increase plant availability. If 

WP251 is being operated with a SIMATIC S7-1200 and stand-alone operation is additionally 

activated, WP251 can also continue operating (filling and dosing) without restrictions if the 

CPU stops because a directly connected HMI device provides access to the module in this 

situation. 
The SIWAREX WP251 electronic weighing system can also be used in hazardous areas 

(Zone 2). The load cells are supplied intrinsically safe in Zone 1 applications when you use 

the optional Ex interface SIWAREX IS. 

4.2

 

Parameter assignment options 

4.2.1

 

Parameter assignment with the PC 

The scale parameters can be quickly assigned with the convenience of a Windows program 

using the "SIWATOOL V7" PC parameter assignment software. 

Содержание SIWAREX WP251





























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды