manualshive.com logo in svg

Siemens SIWAREX WP251, Руководство пользователя

Поделиться
Скачать
Siemens SIWAREX WP251 Скачать руководство пользователя страница 135

Scale parameters and functions 

8.27 DR 30 Process state 

SIWAREX WP251 
Manual, 12/2015, A5E37203357A 

135

 

Variable 

Note 

Type 

Length 

(bytes) 

RW 

De-

fault 

Min. 

Max. 

Modbus 

registers 

2116 Set point too 

large 

In removal mode there is not 

enough material in the contain-

er at the start of dosing (gross < 

set point) Dosing can still be 

started in this case with the 

"Continue weighing" command 

and ended using "Rest empty-

ing" as soon as no more mate-

rial can be removed from the 

scale. 

B17_7 

1 

rw 

1 

0 

1 

1817 

 - 

 - 

B17_8 

0 

rw 

1 

0 

1 

1817 

 - 

 - 

B17_9 

0 

rw 

1 

0 

1 

1817 

 - 

 - 

B17_10  0 

rw 

1 

0 

1 

1817 

 - 

 - 

B17_11  0 

rw 

1 

0 

1 

1817 

2096 Restore point set  Recovery point has been suc-

cessfully set 

B17_12  0 

rw 

1 

0 

1 

1817 

2097 Restore point 

loaded 

Recovery point (or default val-

ues, if no recovery point) has 

been successfully loaded 

B17_13  0 

rw 

1 

0 

1 

1817 

2098 Standard param-

eters loaded 

Note for the user that the 

standard parameters were 

loaded 

B17_14  0 

rw 

1 

0 

1 

1817 

2099 Factory settings 

loaded 

Note for the user that the facto-

ry settings were loaded 

B17_15  1 

rw 

1 

0 

1 

1817 

Reserve 

Reserve 

FLOAT  4 

rw 

0 

0 

 - 

1818 

8.27

 

DR 30 Process state 

8.27.1

 

Overview 

This data record contains all weight values and related status information of WP251. All 

values are read-only. 

Note 
Data record DR 30 does not have to be read into the PLC via a command! In data record DR 

14 (page 101), the user can select two process variables that will be transmitted 

automatically via the S7-I/O to the CPU and be available there. In addition, the AWI 

((Automatic Weighing Instrument) Status is available cyclically in the I/O (see section 

"Integration in SIMATIC") and can thus be directly used in the PLC program. At the Modbus 

end, the parameters and status information from DR 30 is always current and the registers 

can therefore be read immediately. 

Содержание SIWAREX WP251





























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды