manualshive.com logo in svg

Siemens SIWAREX WP251, Руководство пользователя

Поделиться
Скачать
Siemens SIWAREX WP251 Скачать руководство пользователя страница 124

Scale parameters and functions 

 

8.23 DR 24 Controller and filter parameters 

 

SIWAREX WP251 

124

 

Manual, 12/2015, A5E37203357A 

8.23.6

 

Controller deadband - upper limit 

When proportional controller is activated, a deadband for the controller can be defined. If the 

achieved final weight of a dosing (with check) is below the upper limit of the deadband, the 

controller does not correct the shut-off points. If both limits are at zero, the controller corrects 

after each checked dosing. 

8.23.7

 

Controller deadband - lower limit 

When proportional controller is activated, a deadband for the controller can be defined. If the 

achieved final weight of a dosing (with check) is above the lower limit of the deadband, the 

controller does not correct the shut-off points. If both limits are at zero, the controller corrects 

after each checked dosing. 

8.23.8

 

Reaction when max. corrective action is exceeded 

This parameter defines the controller behavior when the maximum corrective action (DR 24) 

is exceeded in a cycle. The following options are available: 

 

Function 

code 

Meaning 

0  

Control is discontinued for this cycle. 

1 (default) 

The controller controls with the maximum corrective action (DR 24) 

8.23.9

 

Selection for dosing filter 

For shut-off of the "coarse" and "fine" dosing signals, a separate signal branch with its own 

filter settings can be specified. The following options are available: 

 

Function 

code 

Meaning 

0  

The dosing signals are shut off based on net process value 1 (with filter from DR 3) 

1 (default) 

The dosing signals are shut off according to net process value 2 (with filter from DR 

24) 

 
 

 

Note 
Standstill 1 and 2 always reference the gross process value 1 with filter settings from DR 3. 

 

Содержание SIWAREX WP251





























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды