Siemens SIWAREX WL280 Скачать руководство пользователя страница 42

Страница: 42 / 58

Mounting

5.3 Fixing of guide element

RN-S SA

Operating Instructions, 09/2016, A5E32605810A-03

Loosen the top nuts

③

in several cycles and slowly lower the load bearing implement.

NOTICE
Loosening the hexagon nuts
Only loosen the hexagon nuts in turn in very small steps. During the process, note which

hexagon nut is loaded and which is not.
Note:

•

The compact installation units are screwed tight to the brackets.

•

By loosening a hexagon nut, the weight of the bearing implement is distributed

among the other hexagon nuts and is partially increased.

Avoid overloading individual hexagon nuts.

Rotate the top nuts

③

downward. The top plate

①

is lying on the load cell

②

via the

pendulum supports. The respective load cell is loaded.

Tighten the nuts

③

against the bottom nuts

④

. In this way, you prevent the nuts

③

from

rotating upwards due to vibrations.

5.3.6

Fixing of second guide element

Fix the second guide element analogous to the description in Chapter Fixing a guide element

(or the first one) (Page 41).

5.3.7

Checking the installation

Check to ensure that the following items are fulfilled after the installation:

●

It must be possible to move the pivot heads of the turnbuckles by hand, they must not be

tensioned.

Содержание SIWAREX WL280



























































Результаты поиска

Содержание SIWAREX WL280

Отзывы:

Siemens SIWAREX WL280, Руководство по эксплуатации, Страница: 42 / 58

Результаты поиска

Содержание SIWAREX WL280

Отзывы: