Siemens SIWAREX WL280 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 58

Siemens SIWAREX WL280 Скачать руководство пользователя страница 39

Mounting

5.3 Fixing of guide element

RN-S SA
Operating Instructions, 09/2016, A5E32605810A-03

39

5.3

Fixing of guide element

5.3.1

General installation information

Observe the information on installation of the compact installation units (see General

installation information (Page 28) ff.). The guide elements are prepared for flanging onto the

compact installation units. The length of the turnbuckle is set to the distance between the

flanges.
You can flange one or two guide elements.
With one guide element:

●

You can flange a guide element on the front or rear of the compact installation unit. The

rear is recommended since the load cell is then always accessible.

●

You can flange the guide element before or after installation of the compact installation

unit into the scale.

●

You can flange the guide element before or after lowering of the load bearing implement.

Connection is recommended prior to lowering of the top plate since the compact

installation unit is still optimally aligned.

With two guide elements:

●

Carry out installation of the first guide element as described above.

●

Lower the load bearing implement.

●

Install the second guide element.

«
...
37
38
39
40
41
...
»

Содержание SIWAREX WL280



























































Отзывы:

Нет отзывов