Siemens SIWAREX WL280 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 58

Siemens SIWAREX WL280 Скачать руководство пользователя страница 38

Mounting

5.2 Installing the compact installation unit

RN-S SA

38

Operating Instructions, 09/2016, A5E32605810A-03

5.2.8

Checking the installation

DANGER

Personal injury and damage to property
Incorrectly set countersunk head screws lead to erroneous measurements due to blocking

and can lead to the scale overflowing. Personal injury and material damage may occur.

NOTICE
Destruction of the load cells and the installation unit
Check that the load cells and installation unit are installed correctly, e.g. by checking the

mounting dimensions and oscillation distances. Incorrect assembly can lead to destruction

of the load cell and the installation unit.

1.

Check to ensure that the following items are fulfilled after the installation:
–

The load bearing implement must be able to oscillate freely.

–

The countersunk head screws

③

should be located as close as possible to the center

in the bores of the top plate

①

. This gives the top plate ideal freedom of movement

and it prevents any incidental forces from occurring.
To do this, lift the centering washer

②

against the top plate. The installation has been

carried out optimally if the centering washer rests all-over.

Figure 5-9

Lifting protection and pendulum limitation

«
...
36
37
38
39
40
...
»

Содержание SIWAREX WL280



























































Отзывы:

Нет отзывов