Siemens SIWAREX WL280 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 58

Siemens SIWAREX WL280 Скачать руководство пользователя страница 29

Mounting

5.2 Installing the compact installation unit

RN-S SA
Operating Instructions, 09/2016, A5E32605810A-03

29

Depending on the installation conditions, the detailed procedure may deviate from the

following description.
The following actions are required in order to install the compact installation unit.
1.

Preparing the load cell

2.

Preparing the compact installation unit

3.

Installing the load cell in the compact installation unit

4.

Installing the compact installation unit

5.

Lowering the load bearing implement onto the load cell

6.

Checking the installation

The actions are described in detail in the following.

5.2.2

Preparing the load cell

NOTICE
Damage to the load cell
Observe the operating instructions for the load cell.
When mounting the load cell, ensure that you do not damage or cut the cables of the load

cell. Load cells must not be carried by their connecting cables.

A data sheet with the calibration values of the load cell are supplied with each load cell. File

the data sheet with your documents.
1.

Unpack the load cell.

Figure 5-1

RN-S SA load cell

2.

Read the accompanying information sheet.

3.

Read the operating instructions for the SIWAREX WL200 load cells.

«
...
27
28
29
30
31
...
»

Содержание SIWAREX WL280



























































Отзывы:

Нет отзывов