Siemens SIWAREX WL280 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 58

Siemens SIWAREX WL280 Скачать руководство пользователя страница 21

RN-S SA
Operating Instructions, 09/2016, A5E32605810A-03

21

Application planning

4

4.1

Load cell dummies

Principle of operation

Load cells are sensitive sensors. To protect the load cells from becoming damaged during

installation and transport, the load cells should only be installed at the last minute. During

installation and transport, the load cells should therefore be replaced by space holders, so-

called dummies or phantoms.
Dummies might be designed as follows:

●

A copy of the installation unit by means of a welded construction for coarse installation

work

●

Use of a SIWAREX WL280 compact installation unit for light installation work

A copy of the installation unit by means of a welded construction

A piece of pipe or some other steel profile is welded between two plates with the hole pattern

for the fixing screws. The total height corresponds to the installation height of the installation

unit. This is the most stable and secure version. Rough installation work can be carried out

with the welded construction.

Use of a SIWAREX WL280 compact installation unit

The compact installation units are delivered pre-assembled. Compact installation units are

set to the installation height of the operational unit. With compact installation units, light

installation work can be carried out.

4.2

Lifting protection

Lifting protection is integrated in the compact installation units for the load cells of the

SIWAREX WL280 series. When other installation units are used, lifting protection must be

provided for in the design if applicable.
The following figure shows a proposed solution for lifting protection. The X designates the

possible lifting path of the load bearing implement. The bore ØD must be larger than the

diameter of the bolt Ød. The movement of the load bearing implement must not be hindered.

«
...
19
20
21
22
23
...
»

Содержание SIWAREX WL280



























































Отзывы:

Нет отзывов