manualshive.com logo in svg

Siemens SIWAREX WL230 BB-S SA, Руководство по эксплуатации

Поделиться
Скачать
Siemens SIWAREX WL230 BB-S SA Скачать руководство пользователя страница 14

2.5

Damage to load cells, measurement errors

NOTICE
Damage to load cells, measurement errors

Dirt must not be allowed to accumulate in the vicinity of a load cell.

Do not subject cable glands and seals to the jet from a pressure washer.

2.6

Specific conditions of use

1. Using the box provided on the nameplate, the User shall permanently mark the type of 

protection chosen for the specific installation. Once the type of protection has been marked 
it shall not be changed.

№ RU C–DE.BH02.B.00316/20

OC НАНИО «ЦСВЭ»

Ex ia IIIC T73°C Da X

0 Ex ia IIC T4 Ga X

2813

FM09ATEX0040X / FM09ATEX0041X
II 1G Ex ia IIC T4 G a
II 1D Ex ia IIIC T

200

135°C Da

II 3G Ex ic IIC T4 Gc

A5E34794967A-2014X

II 3G Ex nA IIC T4 Gc
II 3D Ex tc IIIC T73°C Dc
-20°C ≤ Ta ≤ +40°C  

FM21US0086X
FM21CA0056X

For the US-Zone 20, AEx ia IIIC T135°C Da
For Canada-Ex ia IIIC T 135°C D a

IS CL I,II,III, DIV 1, GP A,B,C,D,E,F,G,T4
IS CL I, ZN 0, AEx/Ex ia IIC T4 Ga
CL I,II,III, DIV 2, GP A,B,C,D,F,G, T4

US & CA
CL I, ZN2, GP IIC T4
IS CL I, ZN 2, AEx/Ex ic IIC T4 Gc

IP6X

0518

FM21UKEX0173X

UK Importer : 
Siemens plc, Manchester M20 2UK, UK

FM21UKEX0174X

Install per Control Drawing A5E51333396A

Refer to manual

Figure 2-1

Nameplate example with box

2. The load cells do not have an earth ground terminal or conductor. The load cells shall be earth 

grounded as part of the final installation.

3. The non-metallic surfaces on the Load Cell’s enclosure may cause risk from electrostatic 

discharge. Avoid installation that could cause electrostatic build-up, and only clean with a 
damp cloth.

Note

The resistance between all safety ground connections and the system grounding electrode shall 
not exceed 1 ohm.

Note

The associated apparatus shall be a single entity-Approved/Certified associated apparatus device 
with outputs that are Approved/Certified for parallel connection of field wiring within the 
applicable hazardouslocation / explosive atmosphere Within the United States,the voltage and 
current parameters of such associated apparatus are commonly identified using the parameters 
Vt (voltage, total) and It (current, total) The use of multiple associated apparatus that are not 
Approved/Certified for use in combination with one another as a system is only permitted as 
specified below.

Safety instructions
2.6 Specific conditions of use

SIWAREX WL200

14

Operating Instructions, 12/2021, A5E02199611B-13

Содержание SIWAREX WL230 BB-S SA



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды