Siemens SIWAREX WL200 Series Скачать руководство пользователя страница 41

Страница: 41 / 102

SIWAREX WL200
Operating Instructions, 07/2016, A5E02199611B-03

Error messages and troubleshooting

8.1

Repair

Note
Unnecessary costs for repairs
Please only return faulty load cells to our repair center accompanied by an accurate

description of the fault. This simplifies the diagnostics.

8.2

Error messages

Rated load exceeded

If load cells are loaded beyond their rated load, this can result in an error message in the

weighing module.
When step changes in load cannot be excluded during measuring, for example, due to

application of a load in free fall, appropriate precautions to avoid damage to the load cell

must be made, e.g. by using elastomer bearings or load cells dimensioned for higher rated

loads.

Wire break

The weighing module reports a wire break if the jumpers are not installed in load cells with

four-wire technology. For details, see section Connecting up (Page 24).

8.3

Checking the mechanical and electrical configuration

In the case of faulty measurements, check the following:

●

Do any force bypasses exist, e.g. due to cables, pipes or guides, that generate forces in

the measuring direction?

●

Are there any other disturbances due to soiling or thermal expansion?

●

Have all load cells been correctly aligned horizontally and at the same height?

●

Has moisture penetrated the junction box?

●

Are the cables connected correctly?

●

Are the cables damaged?

Содержание SIWAREX WL200 Series







































































































Результаты поиска

Содержание SIWAREX WL200 Series

Отзывы:

Бренды по названию

Популярные бренды

Siemens SIWAREX WL200 Series, Руководство по эксплуатации

Результаты поиска

Содержание SIWAREX WL200 Series

Отзывы:

Бренды по названию

Популярные бренды