Siemens SIWAREX FTC Скачать руководство пользователя страница 89 | Manualshive

Страница: 89 / 149

Siemens SIWAREX FTC Скачать руководство пользователя страница 89

W

EIGHING

F

UNCTIONS AND

P

ARAMETERS

5.15.12 DR 30 - Nominal Load

From the nominal flowrate (defined in DR 5) and nominal speed (defined in DR 5)
calculated nominal belt load in the dimension weight unit/length unit [WU/LU].

5.15.13 DR 30 - Belt Load

The current belt load is output as the relationship of the currently measured weight
to the effective belt length. The dimension is: Weight unit/Length unit [WU/LU].

5.15.14 DR 30 – Flowrate 1

The current flowrate 1 is output in the dimension Weight unit / sec [WU/s].

5.15.15 DR 30 – Flowrate 2

The current flowrate 2 is output in the dimension Weight unit/h [WU/h].

5.15.16 DR 30 – Flowrate 3

The current flowrate 3 is output in the dimension Large Weight Unit / h [LWU/h].

5.15.17 DR 30 – Flowrate in % of the Nominal Flowrate

The current flowrate is output in % of the nominal flowrate.

5.15.18 DR 30 – Operating Hours Counter

The operating hours counter records the number of hours that the SIWAREX FTC
is supplied with 24V voltage.

5.15.19 DR 30 – Pulse Counter Value

Current counter value on the pulse input in relation to the defined measurement
time.

5.16 DR 31 Process Status 2 (all operating modes)

The user or the service technician can retrieve information on the current status of
the scale in the expanded process values.

Name

Type

Address Range of Values / Meaning

Reference

Unfiltered digital value

DINT

DBD000

Unfiltered digital value from ADU

Filtered digital value

DINT DBD004

Filtered digital value from filter level 1 for
NAWI-Fct.

Reserve33_1

DINT DBD008

Reserved

Operating error

DWORD DBD012

Error word Operating error (for test dept.,
Bit-No. = Error code –1)

curr. Date/Time

DATE_A

ND_TIME

DBD016

curr. Date/Time

Current temperature

INT DBW024

Current inner-temperature of the module
[0.1°C]. If no temperature value is available: -
100.0°C.

SIWAREX FTC

5-77

«
...
87
88
89
90
91
...
»

Содержание SIWAREX FTC






















































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды